Toshiba B-SX4T-QP manual A1.3.2 Detection Area of the Transmissive Sensor, Label

APPENDIX 1 SPECIFICATIONS	ENGLISH VERSION EO1-33034
	A1.3 Media

A1.3.1		Media Type (Cont.)					[Unit: mm]
		Label dispensing mode		Batch mode	Strip mode	Cut mode
	Item					Rotary cutter (*2)	Swing cutter
	cMedia pitch		Label	10.0 – 1500.0	25.4 – 1500.0	3”/sec., 6”/sec.: 38.0 - 1500.0	38.0 – 1500.0
			Tag	10.0 – 1500.0	----	3”/sec., 6”/sec.: 30.0 – 1500.0	25.4 – 1500.0
	d
	eMedia length			8.0 – 1498.0	23.4 – 1498.0	3”/sec., 6”/sec.: 25.0 – 1498.0	25.0 – 1498.0 (*1)
	fWidth including backing paper (See NOTE 5.)			30.0 – 112.0	50.0 – 112.0	30.0 – 112.0
	gLabel width (See NOTE 5.)			27.0 – 109.0	47.0 – 109.0	27.0 – 109.0
	hGap length			2.0 – 20.0		6.0 – 20.0
	iBlack mark length (Tag paper)					2.0 – 10.0
	Effective print width					10.0 – 104.0 ±0.2
	jEffective print length		Label	6.0 – 1496.0	21.4 – 1496.0	3”/sec., 6”/sec.: 23.0 - 1496.0	23.0 – 1496.0
			Tag	8.0 – 1498.0	----	3”/sec., 6”/sec.: 28.0 – 1498.0	23.0 – 1498.0
	k
	Print speed up/slow down area					1.0
	Thickness		Label			0.13 – 0.17
			Tag			0.15 – 0.29
	Maximum effective length for on the fly issue					1361.0
	Maximum outer roll diameter					Ø 200
	Roll direction					Inside
	Inner core diameter					Ø 76.2±0.3

NOTES:

1.To ensure print quality and print head life use only TOSHIBA TEC specified media.

2.The media length specifications for use of the cutter are:

*1: When issuing a label using the swing cutter, label length should be 35.0 mm – (Gap length/2).

*2: The rotary cutter does not support the print speed of 10”/sec.

When using the Rotary Cutter, be sure to install the Ribbon Saving Module (B-9904-R-QM). Failure to do this may cause a paper jam or ribbon error.

3.When marking black marks on the label rolls, they should be marked at the gaps.

4.“On the fly issue” means that the printer can feed and print without stopping between labels.

5.There are restrictions in use of the media which is narrower than 50 mm. For details, refer to TOSHIBA TEC service representative.

A1.3.2 Detection Area of the Transmissive Sensor

The Transmissive Sensor is movable from the centre to the left edge of media.

The Transmissive Sensor detects a gap between labels, as illustrated below.

<Label>			Area to be detected.			Centre of media
	Sensor position					Print side
	Min. 2.0 mm			Label
				Gap
(Min. 6.0 mm when using
	the cutter module.)			Label
		Min. 12 mm				Media feed direction
					Sensor is movable
					within this range.

EA1- 3