Toshiba DR430 owner manual Others, You press OPEN/CLOSE a, Repairing process MAY not work

				TROUBLESHOOTING
		Symptom			Remedy
HDMI
No image from HDMI connection.					• Check the HDMI connection. (Check the status of the HDMI related
					indications.)
					• Check whether the connected monitor device or other device supports
					HDCP. (This unit will not output a video signal unless the other device
					supports HDCP.)
					• Check the setting of HDMI.
					• Check whether the output format of this unit (HDMI FORMAT) matches the
					supported input format of other connected device.
					• If the unit is connected to the unauthorized display device with an HDMI
					cable, the audio/video signal may not be output when playing back a
					commercial DVD-video.
There is no sound or the sound is					• The HDMI sound is not output when “HDMI Audio” is set to “OFF”.
distorted.					• Check the RCA audio cable connection. If you are using HDMI-DVI conversion
					cable, you must connect the RCA audio cable, too.
					• Check whether the output format of this unit (HDMI FORMAT) matches the
					supported input format of other connected device.
Others
The unit does not operate					• When static electricity, etc., causes the unit to operate abnormally, unplug
properly.					the unit and then plug it in again.
The disc tray does not open when					• It may take a few seconds for the disc tray to open after you have recorded or
you press [OPEN/CLOSE A]					edited a disc. This is because the unit is adding disc data to the disc.
“Repairing” appears on the TV					• If there is a power failure or unplugging during recording, finalizing,
screen.					formatting or editing (even after “Repairing” disappears), a repairing process
					will begin automatically just after turning the unit on again.
					It may take several minutes up to about several hours.
	Repairing
In case you intend to cancel the					• If you intend to cancel the repairing process, press [AOPEN/CLOSE]
repairing process.					on the front panel, then select “Yes” and press [ENTER]. After that, press
					[OPEN/CLOSE A] to take out the disc. The disc canceled during the
		Do you want to cancel a repairing			repairing process MAY NOT work.
		process ? When selecting “Yes”,
		the disc may not be usable.
			Yes
			No
	Repairing

Disc Introduction Connections Basic Setup Management Recording Playback

Error message	Cause	Solution
Disc Error	• Unplayable disc is inserted in the unit.	• Insert the standardized disc which have
— Please eject the disc. —	• The disc is upside down.	the marks on pages 9-10.
Playback feature may not be available on this disc.		• Insert the disc with the labeled side facing up.
Unknown USB Device/File	• Format of the files in the connected	• Insert a compatible USB device with
— Please Remove the USB. —	USB device are not supported.	supported file format. If this does not
Insert a compatible USB device.	• Incompatible USB device is connected.	solve the problem, use other type of
		compatible USB device.
Region Error	• Playback is not authorized in the region	• Insert the DVD-video with region codes
— Please eject the disc. —	of the DVD-video which you inserted in	1 or ALL.
Playback is not authorized in your region.	the unit.
Parental Lock On	• The current selected parental level	• Check “Parental Lock” setting in
The current selected parental level	prohibits playback.	“Playback” menu (page 84).
prohibits playback.
Recording Error	• You are trying to record the copy	• You cannot record copy prohibited
This program is not allowed to be recorded.	prohibited program.	programs.
Recording Error	• You are trying to record the copy-once	• Set “Format Mode” to “VR mode” (page
This program is not recordable in Video	program onto the DVD-RW disc in video	27).
mode.	mode.
Recording Error	• You are trying to record the copy-once	• Insert the DVD-RW disc in VR mode
This program is not recordable in +VR mode.	program.	(ver.1.1 or 1.2 compatible with CPRM).

Editing Function Setup Others

EN 95

E7PEAUD_DR430KU_EN.indd 95

2009/12/14 18:34:11