ADSL2/2+ Ethernet Router User Guide | TP-Link TD-8816 instruction

Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button.

TD-8816

ADSL2/2+ Ethernet Router User Guide

Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button.

Figure 3-8

Step 2: Configure the time for the Router, and then click the NEXT button.

Figure 3-9

Step 3: Select the connection type to connect to the ISP (We select PPPoE/PPPoA mode for example here), and then click the NEXT button.

Figure 3-10

Step 4: Configure the following options provided by your ISP: Username, Password, VPI, VCI and Connection Type. Then click Next.

10

Image 16

TP-Link TD-8816 manual ADSL2/2+ Ethernet Router User Guide

Contents

TD-8816 ADSL2/2+ Ethernet Router Rev1.0.2 1910010149 COPYRIGHT & TRADEMARKS FCC STATEMENT CE Mark Warning Package Contents CONTENTS Chapter 2. Hardware InstallationChapter 3. Quick Installation Guide Chapter 1. Introduction Appendix A Specification Diagnostic4.6.4 4.6.5 1.2 Main Features Chapter 1. Introduction1.1 Product Overview ADSL 1.3 Conventions Chapter 2. Hardware Installation 2.1 The Front Panel2.2 The Back Panel LED Explanation 2.3 Installation Environment 2.4 Connecting the Router TD-8816 Chapter 3. Quick Installation Guide 3.1 Configure PC TD-8816 Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 2 Is the TCP/IP configuration for your PC correct? 3.2 Login1 Is the connection between your PC and the Router correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 5 Click NEXT to finish the Quick Start Chapter 4. Software Configuration 4.1 Status 4.2 Quick Start 4.3 Interface Setup4.3.1 Internet the next screen shown in Figure 1. Dynamic IP Address ¾ TCP MTU Option Enter the TCP MTU as your desire 2. Static IP Address for WAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format3. PPPoA/PPPoE TD-8816 4.3.2 LAN 4. Bridge Mode TD-8816 IP Pool Count The max user pool size If you select Disabled, the DHCP function will not take effect 4.4.1 Firewall 4.4 Advanced Setup4.4.2 Routing 4.4.3 NAT 4.4.3.1. DMZ ¾ Virtual Circuit Enter Virtual Circuit Index that you plan to setup for the NAT function4.4.3.2. Virtual Server Server in the next screen Other configurations for the entries as shown in FigureTo add a virtual server entry 4.4.3.3. IP Address Mapping To add a mapping rule 4.4.4 QoS 4.4.5 VLAN 1. Assign VLAN PVID for each Interface can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. There are two types of VLAN as follows2. Define VLAN Group 4.4.6 ADSL 4.5 Access Management 4.5.1 ACL 4.5.2 Filter 4.5.2.1. IP Filter ¾ Interface Select the interface for the entry ¾ Rule Type For IP Filter, please select IP here To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry 4.5.2.2. MAC Filter To add a MAC Address filtering entry Step 4 Finally, click the SAVE to save the entry 4.5.2.3. Application Filter ¾ Application Filter Activate or deactivate the function 4.5.2.4. URL 4.5.3 SNMP To add a URL filter entry 4.5.4 UPnP 4.5.5 DDNS 4.5.6 CWMP 4.6 Maintenance 4.6.1 Administration 4.6.2 Time Zone 1. NTP Server automatically 2. PC’s Clock 4.6.3 Firmware3. Manually 4 The router will reboot after the upgrading has been finished To upgrade the routers firmware, follow these instructions belowTo back up the Router’s current settings 4.6.4 System Restart To restore the Router’s settings 4.6.5 Diagnostic 4.7 Help TD-8816 General Appendix A SpecificationPhysical and Environment