TL-WR940N Wireless N Router, 47 Host Settings | TP-Link guide

4.11.2 Host

TL-WR940NWireless N Router

4.Click “Access Control → Rule” in the left to return to the Access Control Rule Management page. Select “Enable Internet Access Control” and choose "Deny the packets not specified by any access control policy to pass through the Router".

5.Click Add New... button to add a new rule as follows:

zIn Rule Name field, create a name for the rule. Note that this name should be unique, for example Rule_1.

zIn Host field, select Host_1.

zIn Target field, select Target_1.

zIn Schedule field, select Schedule_1.

zIn Action field, select Allow.

zIn Status field, select Enable.

zClick Save to complete the settings.

Then you will go back to the Access Control Rule Management page and see the following list.

4.11.2 Host

Choose menu “Access Control → Host”, you can view and set a Host list in the screen as shown in Figure 4-47.The host list is necessary for the Access Control Rule.

Figure 4-47 Host Settings

¾Host Description - Here displays the description of the host and this description is unique.

¾Information - Here displays the information about the host. It can be IP or MAC.

¾Modify - To modify or delete an existing entry.

To add a new entry, please follow the steps below.

1.Click the Add New… button.

2.In the Mode field, select IP Address or MAC Address.

z If you select IP Address, the screen shown is Figure 4-48.

1)In Host Description field, create a unique description for the host (e.g. Host_1).

-66-

Image 74

TP-Link manual TL-WR940N Wireless N Router, To add a new entry, please follow the steps below, 47 Host Settings

Contents

TL-WR940N Wireless N Router Rev 1.1.0 COPYRIGHT & TRADEMARKS FCC STATEMENT National restrictions FCC RF Radiation Exposure StatementCE Mark Warning Country NCC Notice Industry Canada StatementKorea Warning Statements ETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN 550222006 +A12007 DECLARATION OF CONFORMITYETSI EN 300 328 V1.7.1 EN 550241998+A12001+A22003 EN 61000-3-22006+A12009+A22009 EN Chapter CONTENTSPackage Contents 4.6.5 4.15.1 Package Contents TL-WR940N Wireless N Router Chapter 1.Introduction Flexible Access ControlSimple Installation 1.1 Overview of the Router 1.4.1 The Front Panel 1.3 Main Features1.4 Panel Layout TL-WR940N Wireless N Router1.4.2 The Rear Panel Indication ¾ RESET 2.3 Connecting the Router Chapter 2.Connecting the Router2.2 Installation Environment Requirements 2.1 System Requirements Figure 2-1 Hardware Installation of the TL-WR940N Wireless N Router Chapter 3.Quick Installation Guide 3.1 TCP/IP Configuration Figure 3-2 Failure result of Ping command Please check the connection following these stepsFigure 3-1 Success result of Ping command 1. Is the connection between your PC and the Router correct? 3.2 Quick Installation Guide Figure 3-5 Quick Setup Figure 3-6 Choose WAN Connection Type Figure 3-7 Quick Setup - PPPoE Figure 3-8 Quick Setup - MAC Clone Figure 3-9 Quick Setup - MAC Clone Figure 3-10 Quick Setup - Static IP Note Dialog z PSK Password - You can enter ASCII or Hexadecimal characters Figure 3-13 Quick Setup - Finish 4.2 Status Chapter 4.Configuring the Router4.1 Login Please refer to 3.2 Quick Installation Guide 4.3 Quick Setup4.4 QSS Figure 4-1 Router Status I. By PBC Method One Method Two Method Three The QSS Configuration Screen of Wireless Adapter TL-WR940N Wireless N Router II. By PIN Method Two Enter the PIN from my Router added to the network 4.5 Network4.5.1 WAN Figure 4-5 WAN - Dynamic IP Figure 4-6 WAN - Static IP Figure 4-7 WAN - PPPoE Figure 4-8 PPPoE Advanced Settings NSW / ACT - nsw.bigpond.net.au QLD - qld.bigpond.net.au Figure 4-10 L2TP Settings Figure 4-11 PPTP Settings z Dynamic IP - Connections which use dynamic IP address assignment z Static IP - Connections which use static IP address assignment Figure 4-12 LAN 4.5.2 LAN4.5.3 MAC Clone Figure 4-13 MAC Address Clone Only the PC on your LAN can use the MAC Address Clone function 4.6 Wireless4.6.1 Wireless Settings Figure 4-15 Wireless Settings ¾ Mode - Select the desired mode. The default setting is 11bgn mixed 4.6.2 Wireless Security ¾ WPA /WPA2 - Enterprise - It’s based on Radius Server Encryption - You can select either Automatic, or TKIP or AES 4.6.3 Wireless MAC Filtering Figure 4-20 Wireless MAC address Filtering 4. Click the Save button to save this entry 4.6.4 Wireless Advanced to access for Filtering Rules 4.6.5 Wireless Statistics This page will be refreshed automatically every 5 seconds 4.7.1 DHCP Settings4.7 DHCP ¾ Default Domain - Optional. Input the domain name of your network 4.7.2 DHCP Clients List 4.7.3 Address Reservation To modify or delete an existing entry 4.8 ForwardingTo Reserve IP addresses To set up a virtual server entry 4.8.1 Virtual Servers 4.8.2 Port Triggering Figure 4-31 Add or Modify a Virtual Server Entry To add a new rule, follow the steps below 4.8.3 DMZ 3. Incoming Port Range cannot overlap each other 4.8.4 UPnP To assign a computer or server to be a DMZ server 4.9 Security 4.9.1 Basic Security Figure 4-37 Basic Security z z z 4.9.2 Advanced Security 4.9.3 Local Management 4.9.4 Remote Management Figure 4-39 Local Management 4.10Parental Control Figure 4-40 Remote Management To add a new entry, please follow the steps below 7. Click the Save button 4.11Access Control 4.11.1 Rule To add a new rule, please follow the steps below Figure 4-45 Access Control Rule Management Figure 4-46 Add or Modify Internet Access Control Entry 4.11.2 Host Figure 4-47 Host Settings Figure 4-48 Add or Modify a Host Entry Figure 4-49 Add or Modify a Host Entry 4.11.3 Target Figure 4-50 Target Settings Figure 4-51 Add or Modify an Access Target Entry Figure 4-52 Add or Modify an Access Target Entry 4.11.4 Schedule To add a new schedule, follow the steps below Figure 4-55 Advanced Routing 4.12 Advanced RoutingFigure 4-54 Advanced Schedule Settings To add static routing entries Other configurations for the entries4.12.1 Static Routing List 4.13Bandwidth Control 4.12.2 System Routing Table 4.13.1 Control Settings 4.13.2 Rules List To add/modify a Bandwidth Control rule, follow the steps below 4.14IP & MAC Binding Setting4.14.1 Binding Setting To find an existing entry, follow the steps below To add IP & MAC Binding entries, follow the steps belowTo modify or delete an existing entry, follow the steps below Figure 4-64 Binding Setting Figure 4-67 ARP List 4.14.2 ARP ListFigure 4-66 Find IP & MAC Binding Entry 4.15Dynamic DNS 4.15.1 Comexe.cn DDNS To set up for DDNS, follow these instructions 4.15.2 Dyndns.org DDNS 4.15.3 No-ip.com DDNS Figure 4-69 Dyndns.org DDNS Settings Figure 4-71 The System Tools menu 4.16System ToolsFigure 4-70 No-ip.com DDNS Settings 4.16.1 Time Settings To set time manually To set Daylight Saving 4.16.2 DiagnosticTo set time automatically 2. The time will be lost if the router is turned off Figure 4-73 Diagnostic Tools 4.16.3 Firmware Upgrade To upgrade the Routers firmware, follow these instructions below 4. The Router will reboot after the upgrading has been finished 4.16.4 Factory Defaults4.16.5 Backup & Restore 4.16.6 Reboot 4.16.7 Password 4.16.8 System Log Figure 4-80 System Log Figure 4-81 Mail Account Settings 4.16.9 Statistics Figure 4-82 Statistics Statistics Table Appendix A FAQ 1. How do I configure the Router to access Internet by ADSL users? Figure A-4 Virtual Servers 3. I want to use Netmeeting, what do I need to do?Figure A-3 MAC Clone Figure A-5 Add or Modify a Virtual server Entry Figure A-6 DMZ 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the Router field of the Web browser Appendix B Configuring the PCs 1. Install TCP/IP component shown in the Figure below ¾ Setting IP address automaticallyNow you have two ways to configure the TCP/IP protocol below Figure B-2 ¾ Setting IP address manually Figure B-3 Figure B-4 General Appendix C SpecificationsWireless Environmental and Physical Appendix D Glossary identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name