TL-WR941ND Wireless N Router, 15 Wireless Settings | TP-Link

Figure 4-15 Wireless Settings

TL-WR941NDWireless N Router

Figure 4-15 Wireless Settings

¾Wireless Network Name - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to be TP-LINK (XXXXXX indicates the last unique six numbers of each Router’s MAC address). This value is case-sensitive. For example, TEST is NOT the same as test.

¾Channel - This field determines which operating frequency will be used. The default channel

is set to Auto, so the AP will choose the best channel automatically. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.

¾Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.

When you select your local region from the pull-down list, click the Save button, then the Note Dialog appears. Click OK.

Note Dialog

)Note:

Limited by local law regulations, version for North America does not have region selection option.

-37-

Image 46

TP-Link manual TL-WR941ND Wireless N Router, 15 Wireless Settings

Contents

TL-WR941ND Wireless N Router Rev 1.1.0 COPYRIGHT & TRADEMARKS FCC STATEMENT National restrictions FCC RF Radiation Exposure StatementCE Mark Warning Country Korea Warning Statements Industry Canada StatementNCC Notice Page ETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN 550222006 +A12007 DECLARATION OF CONFORMITYETSI EN 300 328 EN 550241998+A12001+A22003 EN 61000-3-22006+A12009+A22009 EN Package Contents CONTENTSChapter DHCP 4.15.2 Package Contents TL-WR941ND Wireless N Router Chapter 1.Introduction Flexible Access ControlSimple Installation 1.1 Overview of the Router 1.3 Main Features Name 1.4 Panel Layout1.4.1 The Front Panel Status ¾ RESET 1.4.2 The Rear Panel 2.3 Connecting the Router Chapter 2.Connecting the Router2.2 Installation Environment Requirements 2.1 System Requirements Figure 2-1 Hardware Installation of the TL-WR941ND Wireless N Router Chapter 3.Quick Installation Guide 3.1 TCP/IP Configuration Figure 3-2 Failure result of Ping command Please check the connection following these stepsFigure 3-1 Success result of Ping command 1. Is the connection between your PC and the Router correct? 3.2 Quick Installation Guide Figure 3-5 Quick Setup Figure 3-6 Choose WAN Connection Type Figure 3-7 Quick Setup - PPPoE Figure 3-8 Quick Setup - MAC Clone Figure 3-9 Quick Setup - MAC Clone Figure 3-10 Quick Setup - Static IP Note Dialog 4.6 Wireless ¾ WPA/WPA2-Personal - Select WPA based on pre-shared passphrase Figure 3-13 Quick Setup - Finish 4.1 Login Chapter 4.Configuring the Router4.2 Status 4.4 QSS 4.3 Quick SetupPlease refer to 3.2 Quick Installation Guide Figure 4-1 Router Status I. By PBC Method One Method Two Method Three The QSS Configuration Screen of Wireless Adapter TL-WR941ND Wireless N Router II. By PIN Method Two Enter the PIN from my Router 4.5.1 WAN 4.5 Networkadded to the network Figure 4-5 WAN - Dynamic IP Figure 4-6 WAN - Static IP Figure 4-7 WAN - PPPoE Figure 4-8 PPPoE Advanced Settings NSW / ACT - nsw.bigpond.net.au QLD - qld.bigpond.net.au Figure 4-10 L2TP Settings Figure 4-11 PPTP Settings z Dynamic IP - Connections which use dynamic IP address assignment z Static IP - Connections which use static IP address assignment Figure 4-12 LAN 4.5.2 LAN4.5.3 MAC Clone Figure 4-13 MAC Address Clone 4.6.1 Wireless Settings 4.6 WirelessOnly the PC on your LAN can use the MAC Address Clone function Figure 4-15 Wireless Settings ¾ Mode - Select the desired mode. The default setting is 11bgn mixed 4.6.2 Wireless Security ¾ WPA /WPA2 - Enterprise - It’s based on Radius Server Encryption - You can select either Automatic, or TKIP or AES 4.6.3 Wireless MAC Filtering Figure 4-20 Wireless MAC address Filtering 4. Click the Save button to save this entry 4.6.4 Wireless Advanced to access for Filtering Rules 4.6.5 Wireless Statistics 4.7 DHCP 4.7.1 DHCP SettingsThis page will be refreshed automatically every 5 seconds ¾ Default Domain - Optional. Input the domain name of your network 4.7.2 DHCP Clients List 4.7.3 Address Reservation To Reserve IP addresses 4.8 ForwardingTo modify or delete an existing entry To set up a virtual server entry 4.8.1 Virtual Servers 4.8.2 Port Triggering Figure 4-31 Add or Modify a Virtual Server Entry To add a new rule, follow the steps below 4.8.3 DMZ 3. Incoming Port Range cannot overlap each other 4.8.4 UPnP To assign a computer or server to be a DMZ server 4.9 Security 4.9.1 Basic Security Figure 4-37 Basic Security z z z 4.9.2 Advanced Security 4.9.3 Local Management 4.9.4 Remote Management Figure 4-39 Local Management 4.10Parental Control Figure 4-40 Remote Management To add a new entry, please follow the steps below 7. Click the Save button 4.11Access Control 4.11.1 Rule To add a new rule, please follow the steps below Figure 4-45 Access Control Rule Management Figure 4-46 Add or Modify Internet Access Control Entry 4.11.2 Host Figure 4-47 Host Settings Figure 4-48 Add or Modify a Host Entry Figure 4-49 Add or Modify a Host Entry 4.11.3 Target Figure 4-50 Target Settings Figure 4-51 Add or Modify an Access Target Entry Figure 4-52 Add or Modify an Access Target Entry 4.11.4 Schedule To add a new schedule, follow the steps below Figure 4-54 Advanced Schedule Settings 4.12 Advanced RoutingFigure 4-55 Advanced Routing 4.12.1 Static Routing List Other configurations for the entriesTo add static routing entries 4.13Bandwidth Control 4.12.2 System Routing Table 4.13.1 Control Settings 4.13.2 Rules List 4.14.1 Binding Setting 4.14IP & MAC Binding SettingTo add/modify a Bandwidth Control rule, follow the steps below To find an existing entry, follow the steps below To add IP & MAC Binding entries, follow the steps belowTo modify or delete an existing entry, follow the steps below Figure 4-64 Binding Setting Figure 4-66 Find IP & MAC Binding Entry 4.14.2 ARP ListFigure 4-67 ARP List 4.15Dynamic DNS 4.15.1 Comexe.cn DDNS To set up for DDNS, follow these instructions 4.15.2 Dyndns.org DDNS 4.15.3 No-ip.com DDNS Figure 4-69 Dyndns.org DDNS Settings Figure 4-70 No-ip.com DDNS Settings 4.16System ToolsFigure 4-71 The System Tools menu 4.16.1 Time Settings To set time manually To set Daylight Saving 4.16.2 DiagnosticTo set time automatically 2. The time will be lost if the router is turned off Figure 4-73 Diagnostic Tools 4.16.3 Firmware Upgrade To upgrade the Routers firmware, follow these instructions below 4.16.5 Backup & Restore 4.16.4 Factory Defaults4. The Router will reboot after the upgrading has been finished 4.16.6 Reboot 4.16.7 Password 4.16.8 System Log Figure 4-80 System Log Figure 4-81 Mail Account Settings 4.16.9 Statistics Figure 4-82 Statistics TL-WR941ND Wireless N RouterStatistics Table Appendix A FAQ 1. How do I configure the Router to access Internet by ADSL users? Figure A-3 MAC Clone 3. I want to use Netmeeting, what do I need to do?Figure A-4 Virtual Servers Figure A-5 Add or Modify a Virtual server Entry Figure A-6 DMZ 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the Router field of the Web browser Appendix B Configuring the PCs 1. Install TCP/IP component shown in the Figure below ¾ Setting IP address automaticallyNow you have two ways to configure the TCP/IP protocol below Figure B-2 ¾ Setting IP address manually Figure B-3 Figure B-4 General Appendix C SpecificationsWireless Environmental and Physical Appendix D Glossary identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name