Industry Canada Statement, NCC Notice | TP-Link TL-WR941ND guide

This device has been designed to operate with the antennas listed below, and having a maximum gain of 3 dBi. Antennas not included in this list or having a gain greater than 3 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.”

Industry Canada Statement

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:

(1)Le dispositif ne doit pas produire de brouillage préjudiciable, et

(2)Ce dispositif doit accepter tout brouillage reçu,y compris un brouillage susceptible de provoquer un fonctionnement indésirable.

NOTE IMPORTANTE:

Déclaration d’exposition aux radiations:

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

Korea Warning Statements

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

III

Image 4

TP-Link TL-WR941ND manual Industry Canada Statement, Korea Warning Statements, NCC Notice

Contents

TL-WR941ND Wireless N Router Rev 1.1.0 COPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure Statement CE Mark WarningNational restrictions Country Korea Warning Statements Industry Canada StatementNCC Notice Page DECLARATION OF CONFORMITY ETSI EN 300 328ETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN 550222006 +A12007 EN 550241998+A12001+A22003 EN 61000-3-22006+A12009+A22009 EN Package Contents CONTENTSChapter DHCP 4.15.2 Package Contents TL-WR941ND Wireless N Router Flexible Access Control Simple InstallationChapter 1.Introduction 1.1 Overview of the Router 1.3 Main Features 1.4 Panel Layout 1.4.1 The Front PanelName Status ¾ RESET 1.4.2 The Rear Panel Chapter 2.Connecting the Router 2.2 Installation Environment Requirements2.3 Connecting the Router 2.1 System Requirements Figure 2-1 Hardware Installation of the TL-WR941ND Wireless N Router Chapter 3.Quick Installation Guide 3.1 TCP/IP Configuration Please check the connection following these steps Figure 3-1 Success result of Ping commandFigure 3-2 Failure result of Ping command 1. Is the connection between your PC and the Router correct? 3.2 Quick Installation Guide Figure 3-5 Quick Setup Figure 3-6 Choose WAN Connection Type Figure 3-7 Quick Setup - PPPoE Figure 3-8 Quick Setup - MAC Clone Figure 3-9 Quick Setup - MAC Clone Figure 3-10 Quick Setup - Static IP Note Dialog 4.6 Wireless ¾ WPA/WPA2-Personal - Select WPA based on pre-shared passphrase Figure 3-13 Quick Setup - Finish 4.1 Login Chapter 4.Configuring the Router4.2 Status 4.3 Quick Setup Please refer to 3.2 Quick Installation Guide4.4 QSS Figure 4-1 Router Status I. By PBC Method One Method Two Method Three The QSS Configuration Screen of Wireless Adapter TL-WR941ND Wireless N Router II. By PIN Method Two Enter the PIN from my Router 4.5.1 WAN 4.5 Networkadded to the network Figure 4-5 WAN - Dynamic IP Figure 4-6 WAN - Static IP Figure 4-7 WAN - PPPoE Figure 4-8 PPPoE Advanced Settings NSW / ACT - nsw.bigpond.net.au QLD - qld.bigpond.net.au Figure 4-10 L2TP Settings Figure 4-11 PPTP Settings z Dynamic IP - Connections which use dynamic IP address assignment z Static IP - Connections which use static IP address assignment 4.5.2 LAN 4.5.3 MAC CloneFigure 4-12 LAN Figure 4-13 MAC Address Clone 4.6.1 Wireless Settings 4.6 WirelessOnly the PC on your LAN can use the MAC Address Clone function Figure 4-15 Wireless Settings ¾ Mode - Select the desired mode. The default setting is 11bgn mixed 4.6.2 Wireless Security ¾ WPA /WPA2 - Enterprise - It’s based on Radius Server Encryption - You can select either Automatic, or TKIP or AES 4.6.3 Wireless MAC Filtering Figure 4-20 Wireless MAC address Filtering 4. Click the Save button to save this entry 4.6.4 Wireless Advanced to access for Filtering Rules 4.6.5 Wireless Statistics 4.7 DHCP 4.7.1 DHCP SettingsThis page will be refreshed automatically every 5 seconds ¾ Default Domain - Optional. Input the domain name of your network 4.7.2 DHCP Clients List 4.7.3 Address Reservation To Reserve IP addresses 4.8 ForwardingTo modify or delete an existing entry To set up a virtual server entry 4.8.1 Virtual Servers 4.8.2 Port Triggering Figure 4-31 Add or Modify a Virtual Server Entry To add a new rule, follow the steps below 4.8.3 DMZ 3. Incoming Port Range cannot overlap each other 4.8.4 UPnP To assign a computer or server to be a DMZ server 4.9 Security 4.9.1 Basic Security Figure 4-37 Basic Security z z z 4.9.2 Advanced Security 4.9.3 Local Management 4.9.4 Remote Management Figure 4-39 Local Management 4.10Parental Control Figure 4-40 Remote Management To add a new entry, please follow the steps below 7. Click the Save button 4.11Access Control 4.11.1 Rule To add a new rule, please follow the steps below Figure 4-45 Access Control Rule Management Figure 4-46 Add or Modify Internet Access Control Entry 4.11.2 Host Figure 4-47 Host Settings Figure 4-48 Add or Modify a Host Entry Figure 4-49 Add or Modify a Host Entry 4.11.3 Target Figure 4-50 Target Settings Figure 4-51 Add or Modify an Access Target Entry Figure 4-52 Add or Modify an Access Target Entry 4.11.4 Schedule To add a new schedule, follow the steps below Figure 4-54 Advanced Schedule Settings 4.12 Advanced RoutingFigure 4-55 Advanced Routing 4.12.1 Static Routing List Other configurations for the entriesTo add static routing entries 4.13Bandwidth Control 4.12.2 System Routing Table 4.13.1 Control Settings 4.13.2 Rules List 4.14.1 Binding Setting 4.14IP & MAC Binding SettingTo add/modify a Bandwidth Control rule, follow the steps below To add IP & MAC Binding entries, follow the steps below To modify or delete an existing entry, follow the steps belowTo find an existing entry, follow the steps below Figure 4-64 Binding Setting Figure 4-66 Find IP & MAC Binding Entry 4.14.2 ARP ListFigure 4-67 ARP List 4.15Dynamic DNS 4.15.1 Comexe.cn DDNS To set up for DDNS, follow these instructions 4.15.2 Dyndns.org DDNS 4.15.3 No-ip.com DDNS Figure 4-69 Dyndns.org DDNS Settings Figure 4-70 No-ip.com DDNS Settings 4.16System ToolsFigure 4-71 The System Tools menu 4.16.1 Time Settings To set time manually 4.16.2 Diagnostic To set time automaticallyTo set Daylight Saving 2. The time will be lost if the router is turned off Figure 4-73 Diagnostic Tools 4.16.3 Firmware Upgrade To upgrade the Routers firmware, follow these instructions below 4.16.5 Backup & Restore 4.16.4 Factory Defaults4. The Router will reboot after the upgrading has been finished 4.16.6 Reboot 4.16.7 Password 4.16.8 System Log Figure 4-80 System Log Figure 4-81 Mail Account Settings 4.16.9 Statistics Figure 4-82 Statistics TL-WR941ND Wireless N RouterStatistics Table Appendix A FAQ 1. How do I configure the Router to access Internet by ADSL users? Figure A-3 MAC Clone 3. I want to use Netmeeting, what do I need to do?Figure A-4 Virtual Servers Figure A-5 Add or Modify a Virtual server Entry Figure A-6 DMZ 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the Router field of the Web browser Appendix B Configuring the PCs 1. Install TCP/IP component ¾ Setting IP address automatically Now you have two ways to configure the TCP/IP protocol belowshown in the Figure below Figure B-2 ¾ Setting IP address manually Figure B-3 Figure B-4 Appendix C Specifications WirelessGeneral Environmental and Physical Appendix D Glossary identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name