Transition Networks AR-CF-02(SC) technical specifications AR-CF-02, AR-CF-02SC, AR-CF-02SM

Five years

MEDIA CONVERTER TECHNICAL SPECIFICATIONS

Standards	ANSI/ATA 878
Delay	300ns one-way
Case dimensions	4.75" x 3.0" x 1.0" (119mm x 76mm x 25mm)
Shipping Weight	2 pounds (0.9 kilograms)
Environment	Temperature:	0-40°C (32° to 104° F )
	Humidity	10-90%, non condensing
	Altitude	0-10,000 feet

Warranty

Power Supply Requirements Replace power supply with only the equivalent input rating (see below) and output rating (regulated 9VDC at 0.2 A).

TN PN	Requirement	Location
3525	240 volts, 50 hertz	United Kingdom
3525	230 volts, 50 hertz	Europe

Minneapolis, MN 55344 USA

ARCNET® Coax Copper/Fiber Media Converter

AR-CF-02, AR-CF-02(SC), AR-CF-02(SM)

USER’S GUIDE

The TRANSITION Networks ARCNET® Coax Copper/Fiber Media Converter (AR-CF-02) extends the signal distance of an ARCNET® segment or node link up to 2 kilometers over fiber*, up to 600 meters over coax cable in a star topology, and up to 300 meters over coax cable in a bus topology.

A switch on the media converter allows the media converter to be used to terminate the link or node signal.

3518	120 volts, 60 hertz	USA/Canada/Mexico
3514	100 volts, 50-60 hertz	Japan
3525	240 volts, 50 hertz	Australia

NOTE: This product also can be powered by the Transition Networks E-MCR series media converter rack.

Compliance Information

UL Listed

C-UL Listed (Canada)

CISPR/EN55022 Class A

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this

AR-CF-02

Provides a BNC connector to coaxial cable and a set of RX (receive) and TX (transmit) ST connectors to multimode fiber-optic cable.

AR-CF-02(SC)

Provides a BNC connector to coaxial cable and an RX (receive) and TX (transmit) SC connector to multimode fiber-optic cable.

ArcNet CoaxtoFiber	ConverterMedia	-02
		AR-CF
®

AR-CF-02(SM)

Provides a BNC connector to coaxial cable and an RX (receive) ST and TX (transmit) SC connector to singlemode fiber-optic cable.

equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Copyright Restrictions

© 1999 TRANSITION Networks.

All rights reserved. No part of this work may be reproduced or used in any form or by any means – graphic, electronic, or mechanical – without written permission from TRANSITION Networks.

Trademark Notice

ARCNET is a registered trademark of Datapoint Corporation.
All registered trademarks and trademarks are the property of their respective owners.	33095.B

STATUS LEDS
Power	Steady green LED indicates connection to external AC power.
Coax	Blinking green LED
			Power
	indicates network
		TX RX
	traffic on coaxial cable
	link.
		Fiber	10BASE-T
Fiber	Blinking green LED		Coax
	indicates network traffic on fiber link.

*Consider carefully the network constraints imposed by the maximum latency response time of installed equipment. Some equipment cannot handle the extended response time that 2 kilometers of fiber introduces.