Transition Networks E-TX-MC01 warranty

TRANSCEIVER TECHNICAL SPECIFICATIONS

Standards	IEEE 802.3
Case dimensions	2.8" x 1.75" x 0.75" (71mm x 43mm x 18mm)
Maximum in series:	Two (2)
Environment	Temperature:	0-40°C (32° to 104° F )
	Humidity	10-90%, non condensing
	Altitude	0-10,000 feet
Warranty	Five years

Setting the Transceiver Physical Address

Minneapolis, MN 55344 USA

Fast Ethernet™ Copper Transceiver

E-TX-MC01

USER’S GUIDE

TRANSITION Networks copper transceivers (E-TX-MC01) connect Fast Ethernet™ hubs and/or terminal devices, through a Media Independent Interface (MII) connector, to 10BASE-Tcopper cable or to 100BASE-TXcopper cable.

Additive switch settings allow a physical address to be set by selecting (or not selecting) among the following:

Switch 1 DOWN	20	1	Address (1-5)
			1 2 3	4	5	6	7
Switch 2 DOWN	21	2
Switch 3 DOWN	22	4
Switch 4 DOWN	23	8
Switch 5 DOWN	24	16	O F F	O F F
In the switch setting shown above, the
transceiver physical address is set to 1 (1+0+0+0+0).

E-TX-MC01

Provides an MII connector and an RJ-

4510BASE- T/100BASE-TX connector to unshielded twisted- pair or shielded twisted-pair copper cable.

Config. Switches

1 2 3 4 5 6 7

PL/FDX

MDI MDI-X

UTP/STP Copper

E-TX-MC01

NOTE: 1=ON, 0=OFF

Compliance Information

UL Listed

A set of switches on the front of the transceiver can be used to set a unique physical address for each transceiver. Transceivers can be configured to

autonegotiate or to force either 10Mb/sec half-duplex mode or 100Mb/sec half-duplex mode.

C-UL Listed (Canada)

CISPR/EN55022 Class A

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications.

An MDI/MDI-X switch on the side of the transceiver can be used to set the copper cable configuration to straight-throughor to crossover.

Status LEDs provide the following information:

Address (1-5)

PL/FDX	Illuminated green LED indicatesthe	1		2	3	4	5
	transceiver is operating in full-duplex		Collision
	mode.				RX	TX	Link

10/100 Illuminated green LED indicates the transceiver is operating at 100Mb/s.

ON

OFF

Power

		PL/FDX
	10/100
100BASE-TX TRANSCEIVER	E-TX-MC01
	Collision

RX

TX

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Copyright Restrictions

© 1998 TRANSITION Networks.

All rights reserved. No part of this work may be reproduced or used in any form or by any means – graphic, electronic, or mechanical – without written permission from TRANSITION Networks.

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners. 33097.B

Collision:	Illuminated green LED indicates	Link
		Power
	signal collisions on the Ethernet
	cable.
RX	Flashing or illuminated green LED indicates packet(s) are being received.
TX	Flashing or illuminated green LED indicates packet(s) are being transmitted.
Link	Illuminated green LED indicates the unit is receiving link pulses from a
	compliant device.
Power:	Illuminated green LED indicates connection to external power