Cable Specifications
The physical characteristics must meet or exceed IEEE 802.3™ specifications.
Copper Cable
Category 3: (Minimum requirement for 10 Mb/s operation)
Gauge | 24 to 22 AWG |
Attenuation | 11.5 dB/100m @ |
Maximum Cable Distance | 100 meters |
Category 5: (Minimum requirement for 100 Mb/s operation) | |
Gauge | 24 to 22 AWG |
Attenuation | 22.0 dB/100m @ 100 MHz |
Maximum Cable Distance | 100 meters |
•
•Shielded (STP) or unshielded (UTP)
•Pins 1&2 and 3&6 are the two active pairs in an Ethernet network .
•Use only dedicated wire pairs for the active pins:
(e.g., blue/white & white/blue, orange/white & white/orange, etc.)
|
|
|
| Crossover Cable | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Twisted Pair #1 |
|
|
| 1 |
| 1 | Twisted Pair #1 |
|
| 1 |
| 1 |
|
|
|
| 2 |
| 2 |
| 2 |
| 2 |
| |||
|
|
|
|
|
|
|
|
|
| ||||
Twisted Pair #2 |
|
|
| 3 |
| 3 | Twisted Pair #2 |
|
| 3 |
| 3 |
|
|
|
|
|
|
|
|
| ||||||
|
|
| 6 |
| 6 |
| 6 |
| 6 |
| |||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 16: Copper Cable Configurations
• Do not use flat or silver satin wire.
WARNING: Visible and invisible laser radiation when open. Do not stare into the beam or view the beam directly or with optical instruments. Failure to observe this warning could result in an eye injury or blindness.
WARNING: Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure.
Fiber cable
Bit Error Rate: |
| |
single mode fiber (recommended): | 9 μm |
|
Multimode fiber (recommended): | 62.5/125 μm |
|
Multimode fiber (optional): | 100/140, 85/140, 50/125 μm | |
1300 nm multimode | ||
Fiber Optic Transmitter Power: | min: | max: |
Fiber Optic Receiver Sensitivity: | min: | max: |
Link Budget: | 11.0 dB |
|
Cable Specifications -- continued
1300 nm multimode | ||
Fiber Optic Transmitter Power: | min: | max: |
Fiber Optic Receiver Sensitivity: | min: | max: |
Link Budget: | 11.0 dB |
|
1310 nm single mode | ||
min: | max: | |
min: | max: | |
Link Budget: | 16.0 dB |
|
1310 nm single mode | ||
min: | max: | |
min: | max: | |
Link Budget: | 26.0 dB |
|
1310 nm single mode | ||
min: | max: 0.0 dBm | |
min: | max: | |
Link Budget: | 29.0 dB |
|
1550 nm single mode | ||
min: | max: 0.0 dBm | |
min: | max: | |
Link Budget: | 29.0 dB |
|
This device is certified by the manufacturer to comply with DHHS Rule 21/CFR, Subchapter J applicable at the date of manufacture.
CAUTION: Visible and invisible laser radiation when open. Do not stare into beam or view directly with optical instruments.
CAUTION: Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure.
The fiber optic transmitters on this device meet Class I Laser safety requirements per
20 | techsupport@transition.com | 21 |
