Manuals / TRENDnet / Computer Equipment / Network Router

TRENDnet TEW-310APBX manual Replacing the antenna with high gain antenna, Locate the two antennas

Models: TEW-310APBX

1 47

Download 47 pages 11.73 Kb

Page 3

1 Locate the two antennas

NOTE

Note: TEW-310APBX functions just like TEW-310APB and the configuration procedures are the same as the TEW-310APB. The only difference between the two models is the TEW-310APBX comes with 2 detachable antennas. Below is the antenna installation instruction.

1 Locate the two antennas

inside the box.

2 Locate antenna connectors

on the unit.

Connectors

3

Screw in antenna by turning the knob clockwise.

4

The antenna should fit securely in place.

Knob

Replacing the antenna with high gain antenna

You can also replace one of the antennas with a higher gain TRENDnet antenna (4dBi Indoor Omni Directional, 6dBi Indoor Patch Directional, or 14dBi Outdoor Directional). At default, both antennas are transmitting/receiving data. When installing the high gain antenna, you can choose to install it on either the left or right antenna position. After that, go to the Access Point's configuration page, select "Advanced Settings", and at the bottom of the page, select the desired antenna position.

3

Image 3

TRENDnet TEW-310APBX Replacing the antenna with high gain antenna, Locate the two antennas, inside the box, on the unit

Contents

2.4 GHz Wireless Access Point + Bridge TEW-310APB TEW-310APBXUsers Guide 5.Using the Configuration Utility CONTENTS1.Package Contents 3.Wireless Basicsinside the box Replacing the antenna with high gain antenna2 Locate antenna connectors 1 Locate the two antennasIf any of the above items are missing, please contact your reseller 1. Package ContentsContents System RequirementsConnections 2. IntroductionFeatures and Benefits LED Indicators 3. Wireless Basics TRENDware Wireless Family of LAN products include Installation ConsiderationsStandards - Based Technology objects that the wireless signal must pass thru may limit range. Typical ranges vary depending on the types of materials and any background RF radio frequency noise in your home or business. The key to maximizing range is to follow these basic guidelines 4. Getting Started please remember that the IP Address for each computer must be inIP ADDRESS Setting Up an Infrastructure Network 5. Using the Configuration Menu Factory Default Setting for the TEW-310APBConfiguration Menu Status Screen with Menu Bar AP name SSID Channel WEP Key Mode Basic SettingsIP Settings Automatically . Or you canSubnet Mask , and Gateway by AP Mode Advanced SettingsAuthentication Type 802.1X SecurityTools Note Please do not interrupt the firmware upgrade processBased on Windows XP Operating System 6. TroubleshootingGateway Address ∙ Select the Hardware Tab ∙ Click Device Manager ∙ Click Properties∙ Select Properties to check that the drivers are installed properly AdaptersCardbus Adapter ∙ Right-click on 22M Wireless4. Resetting the TEW-310APB to Factory Default Settings Microsoft Windows XP Go to Start Control Panel Network Connections Using the Network Setup Wizard in Windows XPSelect Set up a home or small office network 7. Networking BasicsPlease follow all the instructions in this window Click NextClick Next Click Next Enter a Computer description and a Computer nameWorkgroup name Click Next Note Each computer should have a unique Computer namePlease wait while the wizard applies the changes When the changes are complete, click NextFormat the disk if you wish, and click Next Insert a disk into the Floppy Disk Drive, in this case drive APlease wait while the wizard copies the files Page Naming your Computer In Windows XP∙ Click Properties Checking the IP Address in Windows XP/2000 Go to Start All Programs Accessories Command PromptAddress Type Command and click OKAssigning a Static IP Address Control PanelNetwork Connections ∙ Click Properties Connections ∙ Click Properties∙ Right-click on Local Area ∙ Highlight Internet Protocol TCP/IPYou have completed the assignment of a Static IP Address ∙ Input your DNS server address only if you plan to use the Internet∙ Select Obtain an IP address Connecting to a Wireless Network in Windows XPNetwork Connection Internet Protocol TCP/IP click PropertiesConnecting to a Wireless Network in Windows ∙ IP address ∙ Subnet maskProperties select Internet Protocol TCP/IP click Properties Connecting to a Wireless Network with a Wireless Router or an Access Point using a DHCP server in Windows ∙ Select Detect connection to network media Connecting to a Wireless Network in Windows Me and∙ Go to Start Settings Control Panel Double-click select Internet Protocol TCP/IP click Properties∙ Select Detect connection to network media Checking the Wireless Connection by Pinging∙ Select Specify an IP address ∙ IP address ∙ Subnet maskFor Windows Me and Shared Documents folder and Sharing files and folders in the Help andFile and Printer Sharing Ports 8. Technical SpecificationsDiagnostic LED StandardsHumidity DimensionsWeight TemperatureE-mail support@trendware.com 9. Contacting Technical SupportTRENDware Technical Support over the Telephone Tel +1-310-891-1100 TRENDware Technical Support E-mailAddress