IP Settings, Automatically . Or you can | TRENDnet TEW-310APBX

IP Settings

Click Apply if you have made any changes or additions.

Click Cancel to discard the changes.

IP Settings

Click on this tab to change device's IP Addresses.

The default IP Address is 192.168.1.1

LAN IP: If you have a DHCP Server,
such as an Internet Router, on the
network, click Obtain IP
Automatically. Or you can
manually enter the IP address,
Subnet Mask, and Gateway by	Fig. 5.5
clicking Fixed IP.	Fig. 5.5

If the Access Point's LAN IP range is different from the configuration computer's IP range, the computer will not be able to enter the configuration menu using web browser.

DHCP Server: Available only when LAN IP is Fixed IP. Click On to enable the TEW-310APB to assign IP addresses to computers on the network. Click Off to disable this feature.

IP Range: IP address range that the device will distribute (e.g. From 192.168.1.2 To 192.168.1.100). Available when DHCP Server is On.

15

Image 16

TRENDnet TEW-310APBX manual IP Settings, Automatically . Or you can, Subnet Mask , and Gateway by

Contents

TEW-310APB TEW-310APBX 2.4 GHz Wireless Access Point + BridgeUsers Guide CONTENTS 1.Package Contents3.Wireless Basics 5.Using the Configuration Utility Replacing the antenna with high gain antenna 2 Locate antenna connectors1 Locate the two antennas inside the box 1. Package Contents ContentsSystem Requirements If any of the above items are missing, please contact your reseller 2. Introduction Connections Features and Benefits LED Indicators 3. Wireless Basics Installation Considerations TRENDware Wireless Family of LAN products includeStandards - Based Technology objects that the wireless signal must pass thru may limit range. Typical ranges vary depending on the types of materials and any background RF radio frequency noise in your home or business. The key to maximizing range is to follow these basic guidelines please remember that the IP Address for each computer must be in 4. Getting StartedIP ADDRESS Setting Up an Infrastructure Network Factory Default Setting for the TEW-310APB 5. Using the Configuration MenuConfiguration Menu Status Screen with Menu Bar Basic Settings AP name SSID Channel WEP Key Mode Automatically . Or you can IP SettingsSubnet Mask , and Gateway by Advanced Settings AP Mode Authentication Type Security 802.1X Note Please do not interrupt the firmware upgrade process Tools 6. Troubleshooting Based on Windows XP Operating System Gateway Address ∙ Click Properties ∙ Select the Hardware Tab ∙ Click Device Manager Adapters Cardbus Adapter∙ Right-click on 22M Wireless ∙ Select Properties to check that the drivers are installed properly 4. Resetting the TEW-310APB to Factory Default Settings Using the Network Setup Wizard in Windows XP Select Set up a home or small office network7. Networking Basics Microsoft Windows XP Go to Start Control Panel Network Connections Please follow all the instructions in this window Click Next Workgroup name Enter a Computer description and a Computer nameClick Next Note Each computer should have a unique Computer name When the changes are complete, click Next Please wait while the wizard applies the changes Insert a disk into the Floppy Disk Drive, in this case drive A Format the disk if you wish, and click Next Please wait while the wizard copies the files Page Naming your Computer In Windows XP Go to Start All Programs Accessories Command Prompt Checking the IP Address in Windows XP/2000 Type Command and click OK Address Control Panel Assigning a Static IP AddressNetwork Connections ∙ Right-click on Local Area Connections ∙ Click Properties∙ Highlight Internet Protocol TCP/IP ∙ Input your DNS server address only if you plan to use the Internet You have completed the assignment of a Static IP Address Connecting to a Wireless Network in Windows XP Network ConnectionInternet Protocol TCP/IP click Properties ∙ Select Obtain an IP address ∙ IP address ∙ Subnet mask Connecting to a Wireless Network in WindowsProperties select Internet Protocol TCP/IP click Properties Connecting to a Wireless Network with a Wireless Router or an Access Point using a DHCP server in Windows Connecting to a Wireless Network in Windows Me and ∙ Go to Start Settings Control Panel Double-clickselect Internet Protocol TCP/IP click Properties ∙ Select Detect connection to network media ∙ Select Specify an IP address Checking the Wireless Connection by PingingFor Windows XP and Shared Documents folder and Sharing files and folders in the Help and For Windows Me andFile and Printer Sharing 8. Technical Specifications Diagnostic LEDStandards Ports Dimensions WeightTemperature Humidity 9. Contacting Technical Support TRENDware Technical Support over the Telephone Tel +1-310-891-1100TRENDware Technical Support E-mailAddress E-mail support@trendware.com