Contents
Important Safety Instructions
Quick Installation
Optional Installation
Storage and Service
Battery Warnings
SAVE THESE INSTRUCTIONS
UPS Location Warnings
UPS Connection Warnings
1 Plug the UPS into an outlet on a
dedicated circuit
2 Plug your equipment into the UPS
3 Turn the UPS ON
2 EPO Port Connection
Optional Installation
1 USB and RS-232 Serial Communications
Buttons Front Panel
Basic Operation
Indicator Lights Front Panel
Basic Operation continued
Other UPS Features Rear Panel
Basic Operation continued
15/20 amp/120V NEMA 5-20R 20 amp/120V NEMA L5-20R
30 amp/120V NEMA L5-30R
PowerSensitivityAdjustment This dial is normally set fully counter-clockwise, which enables the UPS to provide maximum protection against waveform distortions in its AC input. When such distortion occurs, the UPS will normally switch to providing sine wave power from its battery reserves for as long as the distortion is present. In areas with poor utility power or where the UPS’s input power comes from a backup generator, chronic waveform distortion could cause the UPS to switch to battery too frequently, draining its battery reserves. You may be able to reduce how often your UPS switches to battery due to mod- erate waveform distortion by experimenting with different settings for this dial. As the dial is turned clockwise, the UPS becomes more tolerant of variations in its input power’s AC waveform. NOTE The further the dial is adjusted clockwise, the greater the degree of waveform distortion the UPS will allow to pass to con- nected equipment. When experimenting with different settings for this dial, operate connected equipment in a safe test mode so that the effect on the equip- ment of any waveform distortions in the UPS’s output can be evaluated without disrupting critical operations
Basic Operation continued
Service
Storage
Storage and Service
Warranty Registration
1 Carefully pull the front panel away from the UPS
2 Remove old batteries
Connect new batteries
4 Reassemble UPS
Manual del propietario
Instrucciones de seguridad importantes
Instalación rápida
Instalación opcional
GUARDE ESTAS INSTRUCCIONES
Advertencias sobre la ubicación del UPS
Advertencias sobre la conexión del UPS
Advertencias sobre la conexión de equipos
1 Conecte el UPS en una salida de un circuito dedicado
2 Conecte sus equipos en el UPS
3 Encienda el UPS
Instalación rápida
Instalación opcional
1 Comunicaciones USB y serie RS-232
2 Conexión de puerto EPO
Botones Panel frontal
Operación básica
Operación básica continúa
Luces indicadoras Panel frontal
Otras funciones del UPS Panel posterior
Operación básica continúa
Operación básica continúa
Almacenamiento y servicio
Servicio
Almacenamiento
1 Tire cuidadosamente del panel frontal, hacia afuera y
retirándolo del UPS
2 Quite las baterías viejas
3 Conecte las nuevas baterías
Installation rapide
Installation en option
Entreposage et service
Remplacement de batterie
Mises en garde Emplacement de lUPS
CONSERVER CES DIRECTIVES
Mises en garde Connexions de lUPS
Mises en garde Connexion déquipement
1 Brancher lUPS dans une prise dun
circuit dédié
2 Connecter votre équipement à lUPS
3 Mettre lUPS sous tension
Installation en option
1 Ports de communication de série USB et RS-232
2 Connexion au port EPO
Boutons Panneau avant
Fonctionnement de base
Fonctionnement de base, suite
Voyants indicateurs Panneau avant
20 amp/120V NEMA L5-20R 30 amp/120V NEMA L5-30R
Autres caractéristiques de lUPS panneau arrière
Fonctionnement de base, suite
à léquipement connecté sera important. En expérimentant différents réglages de ce rotateur, faire fonctionner léquipement en mode de test sécuritaire de façon à ce que leffet des dis- torsions de forme donde à la sortie de lUPS sur léquipement puisse être évalué sans perturber les opérations critiques
Fonctionnement de base, suite
Service
Entreposage
Entreposage et service
Avant denvoyer votre UPS pour réparations, suivre ces étapes
1 Tirez délicatement le panneau avant vers le bas et
éloignez-le de lUPS
2 Enlever les anciennes piles
3 Connecter de nouvelles piles
Page
200607046