Replacing Belts

To remove and replace either the auger belt or the drive belt, follow the steps below and then proceed to the specific steps listed under respective sub-headings.

1.Disconnect the chute crank assembly at the discharge chute end by removing the hairpin clip and the flat washer. See Figure 19.

2.Remove the plastic belt cover, located near the engine, by removing the three self-tapping screws and flat washers that secure it. See Figure 23.

3.a. Loosen the bolt shown in Figure 24 securing the belt keeper bracket and remove the other bolt.

b.Push the belt keeper and bracket up off the engine pulley. See Figure 25.

Auger Belt

4.Remove the hairpin clip and flat washer from the ferrule in order to disconnect the auger idler rod from the brake bracket assembly. See Figure 26.

5.Unhook the spring found on the end of the auger cable from its respective actuator bracket. Refer to Figure 12.

6.Slip the auger control belt (the front belt) off the engine pulley.

7.Pull the brake bracket assembly towards the cable guide roller and unhook the auger cable “Z” fitting. See Figure 27.

8.Remove the upper bolts which attach the auger housing assembly to the frame assembly using a 9/16” wrench. Refer to Figure 28.

6

Maintaining

Your Snow

Thrower

IMPORTANT NEVER replace the auger shear pins with standard pins. Any damage to the auger gearbox or other com- ponents, as a result of

Figure 23

Remove

Loosen

Figure 24

Figure 26

 

Figure 25

Figure 27

 

doing so, will NOT be covered by your snow thrower’s warranty.

Check the condition of both auger belt and drive belt every 25 hours of snow thrower operation. Replace if either shows signs of wear and tear.

Specifications are subject to change without notification or obligation. Images may not reflect your exact model and are for refer- ence purposes only.

17

Page 16 Page 18
Page 17
Image 17
Troy-Bilt 769-02528 warranty Replacing Belts, Auger Belt
Page 16 Page 18

769-02528 specifications

The Troy-Bilt 769-02528 is a powerful and versatile tool designed to make outdoor work easier and more efficient. This machine is particularly known for its robust performance in various landscaping tasks, including tilling, planting, and cultivating. With a well-engineered design, it addresses the needs of both amateur gardeners and professional landscapers who require reliable equipment.

One of the standout features of the Troy-Bilt 769-02528 is its potent 208cc engine. This engine provides ample power to tackle tough soil conditions and heavy-duty gardening tasks. The engine is designed for easy starting, which is a significant advantage for users who may not want to deal with the frustrations of traditional pull-start systems. The machine is equipped with a recoil starter that engages smoothly, reducing overall strain during the starting process.

In terms of tilling capabilities, the Troy-Bilt 769-02528 is built with a set of 12-inch hardened steel tines. These tines are engineered for durability and efficiency, allowing the tiller to penetrate deeper into the soil and break up compacted ground easily. The adjustable tilling width offers versatility, enabling users to select the appropriate width for their specific gardening needs. The tilling width can vary from 16 to 21 inches, catering to a range of tasks from small garden beds to larger areas.

An intuitive design is evident in the balance and maneuverability of the Troy-Bilt 769-02528. It comes with a low-profile design, which enhances stability during operation. The adjustable handlebars offer comfort and control as users navigate through their gardens. Additionally, the forward and reverse drive options make it easy to maneuver the tiller in tight spaces and improve overall usability.

Another key technology featured in the Troy-Bilt 769-02528 is its self-propelled feature. This allows the tiller to move on its own, reducing the physical effort required by the operator. The combination of this self-propulsion with variable-speed options makes it suitable for various terrains and soil types, ultimately enhancing productivity.

Overall, the Troy-Bilt 769-02528 combines power, efficiency, and innovative technology to deliver a reliable gardening tool. Its features cater to a wide audience, from seasoned gardeners looking for a dependable helper to those just starting in landscaping. With its solid construction and advanced capabilities, the Troy-Bilt 769-02528 stands out as an essential asset for any outdoor project.
Top Page Image Contents