Figure 4

Attaching the Chute Assembly

•Remove locknuts and screws securing one of the flange keepers to the chute assembly. See Figure 4.

•Loosen but do not remove the locknuts and screws on the other two flange keepers.

•Slide chute assembly over chute opening, making sure the flange keepers are beneath lip of chute adapter. The notches should engage with the spiral end of the chute crank. See Figure 5.

•Secure flange keeper, locknuts and screws previously removed. Tighten all flange keepers and hardware with two 7/16” wrenches. Do not over tighten.

NOTE: If necessary the chute crank support bracket can be adjusted so the spiral on the chute crank fully engages the teeth on the chute assembly. Refer to the Adjustment Section.

Attaching the Shift Rod

•Align the upper and lower shift rods, then slide the shift rod connector down over the end of the lower shift rod. Tap the connector until the lower rod is completely through the connector. See Figure 6.

NOTE: If the connector is not properly assembled, the shift rod will pivot and you will not be able to change speeds or direction.

NOTE: If the full range of speeds (forward and reverse) cannot be achieved, refer to the Adjustment Section.

•Normally the cable ties holding the steering cables against the handle are loosely installed on each side of the lower handle at the factory. Pull the cable ties tight to secure. Cut the excess from the ends of cable ties.

•If not already attached, slip the cables that run from the handle panel to the discharge chute into the cable guide located on top of the engine. See Figure 7.

•Wrap the wire from the head lamp down the right handle until the wire can be plugged into the alternator lead wire under the fuel tank. See Figure 8.

3

Setting Up

Your Snow

Thrower

Figure 5

WARNING

Prior to operating your snow thrower, refer to Auger Control on page 9. Read and follow all instructions carefully and perform all adjustments to verify your unit is operating safely and properly.

Figure 6

Figure 7



Page 6 Page 8
Page 7
Image 7
Troy-Bilt 769-02528 warranty Attaching the Chute Assembly, Attaching the Shift Rod
Page 6 Page 8

769-02528 specifications

The Troy-Bilt 769-02528 is a powerful and versatile tool designed to make outdoor work easier and more efficient. This machine is particularly known for its robust performance in various landscaping tasks, including tilling, planting, and cultivating. With a well-engineered design, it addresses the needs of both amateur gardeners and professional landscapers who require reliable equipment.

One of the standout features of the Troy-Bilt 769-02528 is its potent 208cc engine. This engine provides ample power to tackle tough soil conditions and heavy-duty gardening tasks. The engine is designed for easy starting, which is a significant advantage for users who may not want to deal with the frustrations of traditional pull-start systems. The machine is equipped with a recoil starter that engages smoothly, reducing overall strain during the starting process.

In terms of tilling capabilities, the Troy-Bilt 769-02528 is built with a set of 12-inch hardened steel tines. These tines are engineered for durability and efficiency, allowing the tiller to penetrate deeper into the soil and break up compacted ground easily. The adjustable tilling width offers versatility, enabling users to select the appropriate width for their specific gardening needs. The tilling width can vary from 16 to 21 inches, catering to a range of tasks from small garden beds to larger areas.

An intuitive design is evident in the balance and maneuverability of the Troy-Bilt 769-02528. It comes with a low-profile design, which enhances stability during operation. The adjustable handlebars offer comfort and control as users navigate through their gardens. Additionally, the forward and reverse drive options make it easy to maneuver the tiller in tight spaces and improve overall usability.

Another key technology featured in the Troy-Bilt 769-02528 is its self-propelled feature. This allows the tiller to move on its own, reducing the physical effort required by the operator. The combination of this self-propulsion with variable-speed options makes it suitable for various terrains and soil types, ultimately enhancing productivity.

Overall, the Troy-Bilt 769-02528 combines power, efficiency, and innovative technology to deliver a reliable gardening tool. Its features cater to a wide audience, from seasoned gardeners looking for a dependable helper to those just starting in landscaping. With its solid construction and advanced capabilities, the Troy-Bilt 769-02528 stands out as an essential asset for any outdoor project.
Top Page Image Contents