KT-MOD-OUT16

KT-400 Expansion Module 16-Output with SPI Cable Install Sheet

1.Introduction

The KT-MOD-OUT16is a 16 zones output module. It can be used for elevator access control (may require additional hardware).

The module supports daisy chaining; you can interconnect up to 16 KT-MOD-OUT16 modules for a total of 256 external outputs per KT-400. You can mix relays and outputs in the same SPI group, up to 256 outputs.

Note 1: The KT-400 SPI port maximum current draw, when the 12V AUX terminals are not used, is 500 mA.

Note 2: External power supply (12 VDC, 2 Amps) is required when the total current draw exceeds 500mA on the SPI Port.

Note 3: There are already 4 relays available on the KT-400. Make sure to check the relays number assignments to prevent redundancy unless it has been planned on purpose.

2.Specifications

•Maximum Current draw: up to 750 mA per module

•Connects to the KT-400 via the 6-pin SPI connector

•16 outputs low current module, 5 to 24 VDC, 4 to 750 mA

•Can be used for elevator access control or general output

•Can be mixed with output module KT-MOD-REL8 in the same SPI group

3.Installing the KT-MOD-OUT16

3.1. Unpacking

The KT-MOD-OUT16package includes the following parts:

•One (1) KT-MOD-OUT16 module, 14 cm x 8 cm (5.7 in x 3.25 in)

•One (1) SPI cable with 1 SPI connector, 41 cm (16 in)

•Four (4) plastic standoffs

•Two (2) installation sheets, English and French

3.2. Mounting

The KT-MOD-OUT16can be installed inside a compatible cabinet (KT-MOD-CAB or KT-400) or mounted in a dry and secure location at less than 1 m (3 ft) from the KT-400.

Perform the following steps to mount the unit:

1.Press the four (4) plastic standoffs through the mounting holes of the cabinet,

2.Secure the cabinet to the wall in the desired location. Use appropriate wall anchors when securing the cabinet to drywall, plaster, concrete, brick or other surfaces,

3.Press the module into the plastic standoffs to secure the module to the cabinet.

Once the unit is mounted, wiring may be started.

3.3. Installation and Wiring

Before beginning to wire the unit, ensure that all power (AC transformer and battery) is disconnected from the KT-400.

Perform the following steps to complete wiring:

1.Connect the 6-pin SPI connector to:

•the KT-400 SPI port, or

•the SPI OUT of the previous output module (KT-MOD- REL8 and KT-MOD-OUT16 only), or

•the SPI EXP of the 1st input module KT-MOD-INP16connected to the KT-400 SPI port.

2.Connect the six SPI wires (blue (BLU), white (WHT), green (GRN), yellow (YEL), black (BLK) and red (RED)) to the SPI IN (TB1) terminals.

3.Connect the 6-pin SPI connector from the SPI OUT to the next output module (KT-MOD-REL8and KT-MOD-OUT16 only).

4.Complete all output wiring.

Tel.: 1 (450) 444 2030 • Toll Free: 1-888-222-1560 • Fax: 1 (450) 444 2029 • Internet: www.kantech.com

DN1781-0809

Copyright © 2008 Tyco International Ltd. and its Respective Companies. All Rights Reserved. • Specifications may change without notice.

Kantech and the Kantech logo are trademarks of Tyco International Ltd. and its Respective Companies.

Page 2
Page 1
Image 1
Tyco KT-MOD-OUT16 specifications Unpacking, Mounting, Installation and Wiring
Page 2

KT-MOD-OUT16 specifications

The Tyco KT-MOD-OUT16 is an advanced modular output card specifically designed for use in industrial and commercial applications. As part of the KT series from Tyco, this module offers a versatile solution for controlling multiple outputs, making it an essential component for various automation systems.

One of the standout features of the KT-MOD-OUT16 is its capacity to control up to 16 outputs. Each output can be independently programmed and controlled, providing flexibility for users in diverse applications. This capability makes the module suitable for managing various devices, such as motors, lights, and sensors, thereby streamlining operations in complex systems.

The module employs reliable solid-state output technology, which enhances its durability and performance. This technology minimizes wear and tear compared to traditional electromechanical relays, leading to a longer operational lifespan. Additionally, solid-state outputs can handle high switching frequencies, making the KT-MOD-OUT16 ideal for high-speed applications.

In terms of communication, the KT-MOD-OUT16 supports various protocols, ensuring compatibility with a wide array of control systems. This includes both serial and parallel communication options, allowing seamless integration into existing setups. Such flexibility reduces installation time and simplifies future upgrades or expansions.

Another significant characteristic of the KT-MOD-OUT16 is its comprehensive diagnostic capabilities. The module incorporates built-in monitoring features that provide real-time feedback on output status and health. This functionality enables quick troubleshooting and maintenance, minimizing downtime and ensuring continuous operation of critical systems.

The design of the module emphasizes ease of installation and use. It is compact and lightweight, allowing for efficient use of space within control panels. Furthermore, user-friendly configuration software simplifies the programming process, making it accessible even for those with limited technical expertise.

Overall, the Tyco KT-MOD-OUT16 is a powerful, reliable, and flexible output module that is well-suited for a wide range of industrial applications. With its impressive features, including solid-state technology, multiple communication options, and robust diagnostic capabilities, the KT-MOD-OUT16 stands out as an excellent choice for modern automation needs. It provides users with the tools necessary to streamline their operations, enhance system performance, and ultimately achieve greater efficiency.
Top Page Image Contents