U-Line U-CLRCO2175S-41 Before Calling for Service, If Service is Required, Replacement Parts

Service

Before Calling for Service

If you think your U-Line product is malfunctioning, read the OPERATION section of this guide to clearly understand the function of the control.

If the problem persists, read the NORMAL OPERATING SOUNDS and TROUBLESHOOTING GUIDE section of this guide to help you quickly identify common problems, and possible causes and remedies. Most often, this will resolve the problem without the need to call for service.

If Service is Required

If you do not understand a troubleshooting remedy, or your product needs service, contact U-Line Corporation directly. Contact information appears on the rear cover of this guide.

When you call, you will need your product Model and Serial Numbers. This information can be recorded inside the front cover of this guide. It also appears on the Model and Serial number plate located on the upper right or rear wall of the interior of your product.

Replacement Parts

When you need replacement parts, always request genuine U-Line replacements. U-Line designs and engineers products using components that work efficiently, and provide superior service life and performance. The use of aftermarket parts or components may affect the safety, operation, performance or durability of your product, and may also void its warranty.

Normal Operating Sounds

All models incorporate rigid foam insulated cabinets to provide high thermal efficiency and maximum sound reduction for its internal working components. Despite this technology, your model may make sounds that are unfamiliar.

Normal operating sounds may be more noticeable because of the unit’s environment. Hard surfaces such as cabinets, wood, vinyl or tiled floors and paneled walls have a tendency to reflect normal appliance operating noises.

Listed below are common refrigeration components with brief description of the normal operating sounds they make. NOTE: Your product may not contain all the components listed.

•Compressor: The compressor makes a hum or pulsing sound that may be heard when it operates.

•Evaporator: Refrigerant flowing through an evaporator may sound like boiling liquid.

•Condenser Fan: Air moving through a condenser may be heard.

•Automatic Defrost Drain Pan: Water may be heard dripping or running into the drain pan when the unit is in the defrost cycle.

•Running Water: As your unit continues to produce ice you will hear water flowing into the collection chambers and running over the evaporator.

Troubleshooting Guide

!DANGER

ELECTROCUTION HAZARD. Never attempt to repair or perform maintenance on the unit until disconnecting the main electrical power.

Troubleshooting - What to check when problems occur:

Problem	Possible Cause and Remedy
Unit Does not	No electrical supply. Plug unit in or check circuit
operate.	breaker.
Electronic
display blank
No Interior	CLRCO2175, Tighten or replace bulb, See
light	Maintenance) CLR2160, contact Service.
Display showing	If display shows error 10E or ER, check to make sure
error code	door is sealing correctly. Make sure to close door
	completely. If sealing the door does not clear the
	error, contact U-Line service for more information.
Unit Develops	The unit is exposed to excessive humidity, moisture
Condensation	will dissipate as humidity levels decrease.
on External
surfaces
Product is	Adjust the temperature to a warmer set-point. (See
Freezing in	PRODUCT OPERATION)
Combo Models.
Product is Not	Air temperature does not indicate product
Cold Enough in	temperature. See PRODUCT OPERATION -
Combo Models.	Checking Product Temperature.
	Adjust the temperate to a cooler set-point. (See
	PRODUCT OPERATION)
	Ensure unit is not located in excessive ambient
	temperatures or in direct sunlight.
	Ensure the door is closing and sealing properly.
	Ensure the interior light has not remained on too
	long.
	Ensure nothing is blocking the front grille, found at
	the bottom of the unit.
	Ensure the condenser coil is clean and free of any dirt
	or lint build-up.
Poor Ice quality.	Unit may not be level. Check unit for levelness. (See
	MAINTENANCE) Ice maker system may be dirty.
	Clean the ice maker. (See MAINTENANCE)
No Ice	Ensure water is being supplied to the unit.Verify the
Production	ice making unit is turned on (See PRODUCT
	OPERATION)
Not Enough Ice	Ensure the condenser coil is clean and free of any dirt
	or lint build-up.
Water in Bucket	Drain may be restricted, ensure drain is free of
	foreign debris.

u-line.com 17