Standard wall plate mounting | Uniden EXT1265 specification

Raise the antenna.

Mounting the Base Unit on a Wall

Setting the handset retainer clip for wall mounting

!

DO NOT use an outlet controlled by a

wall switch.

1 On the base unit, pull the handset retainer clip out of the slot and rotate it clockwise 180 degrees.

2 Flip the retainer clip from front to back. Slide it back into the slot so that the lip of the retainer is up and the ª is down. The retainer holds the handset

in place.

Standard wall plate mounting

Flip the hook tab over so the tab holds the handset.

This phone can be mounted on any standard wall plate.

1 Route the AC adapter cord inside the molded wiring channel as shown.

2 Plug the telephone line cord into the TEL LINE jack. Route the cord inside the molded wiring channel as shown.

3 Raise the antenna to a vertical position.

Single-Line Telephone Jack (RJ11C)

Telephone

Line Cord

Power Outlet (AC 120V, 60Hz)

AC Adapter

4 Align the mounting slots on the base with the mounting posts on the wall. Then push in and down until the phone is firmly seated.

[ 10 ] G E T T I N G S TA R T E D

Image 12

Uniden EXT1265 manual Setting the handset retainer clip for wall mounting, Standard wall plate mounting

Contents

Page Page Contents Features Terminology Controls and Functions Talk O N T R O L S a N D F U N C T I O N S Checking the Package Contents Setting up the Phone Do the following stepsChoose the best location Install the battery pack Battery use time per chargeLow battery alert Connect the base unit Choose the dialing mode Base setting only Setting the handset retainer clip for wall mounting Standard wall plate mounting Direct wall mounting Setting Caller ID Options Or Cidcw Off depending upon the type of service to which When the phone is in the standby mode, press menuUse To move the pointer between Auto Talk On or You subscribe Press Ringer Volume Setup Handset Ringer Tone SettingHandset ringer volume setting Base ringer volume setting Distinctive Ringer Setup Use Or ª To select Distinctive On or Int’cm/select to select. The Language setting Selecting a LanguageTo move the pointer to Language Screen appears Making and Receiving Calls From the Handset From the Base Handset On the BaseHandset Off the Base Call Waiting Adjusting Earpiece Volume Base Volume Redialing from Standby Mode Redial from Talk ModeRedialing a Call Last three phone numbers dialed can be quickly redialed Traveling Out-of-Range From the baseTo call the last number dialed from the base Press talk key Using One Touch Voice Mail Access Programming your Voice Mail Access NumberWith the base Dialing your Voice Mail Service Message Waiting IndicatorDeleting the Voice Mail Number With the handset Press int’cm/select to selectForth/back between characters E M O R Y D I a L I N G Memory dialing from Standby Mode With the handset Making Calls with Memory Dialing Memory dialing from Talk Mode Display a Programmed Number while in Memory Location ListPress memory . The memory list is displayed To review the details of a memory location Use To move To selectTo scroll through Memory locations Editing a stored name, phone number or distinctive ring Deleting the stored dataPress to move the pointer to Yes When speaking on the handset When speaking on the baseWay Conferencing Press On the base unit To initiate the 3-way conversation Intercom/Page Feature Intercom from the base to handsetIntercom from the handset to base Base. The handset beeps. If no answer, press Call Transfer Feature Chain DialingTo transfer from the handset to the base To transfer from the base to the handset Tone Dialing Switch-over Mute BaseSelecting a Different Channel When the Telephone Rings You must subscribe to Caller ID service to use this featureCaller ID When you answer the call, the display changes to Talk Viewing the Caller ID Message ListPress caller id to return to standby When the pointer is at Yes When the pointer is at NoDeleting Information from the Caller ID List Deleting a Caller ID message Using the Caller ID List Deleting all Caller ID names/numbersCalling a party from the Caller ID list Tone sounds and all stored Caller ID messages are deleted Long Distance calls and Area Code setting/cancellation Storing Caller ID messages in memory dialing Using Caller ID on Call Waiting Service First caller will be put on holdTo return to the first caller, press call waiting again Call Waiting Deluxe Features For example Accessing Advanced Calling Features Press menu . The following screen appearsUse the or ª key or enter Pre-programmed Calling Features Calling features Display Preprogrammed Activation codesCalling features Activation codes Displaying the pre-programmed activation codes Descriptions of calling features Adding New Features Add or edit a service Restore Svc02? Yes Service02 Restored Changing the Digital Security Code Remove the handset from the base unitPress and hold int’cm/page on the base While the handset is emitting the paging Headset Installation Changing the Face PlateTo remove the Face plate To attach the Face plate Installing the Beltclip Maintenance Battery replacement and handling Power Failure Troubleshooting Symptom Battery Information General InformationAC Adapter Information Precautions Installation Considerations Index K, L Memo At Uniden, we’ll take care of you