USC 2500XL T
OPERATING GUIDE
400-Channel Programmable Hand-Held Auto Scanner
NICKEL-CADMIUM BATTERY WARNING
Battery
PRECAUTIONS
Beforeyou read anythingelse, pleaseobservethe following
Maintenance
Controls and Indicators
Troubleshooting
Specifications
Utility
What is Scanning?
About Your New UBC 2500XLT
Types of Communication
Unpacking
Optional Accessories
Earphone
Spare Battery Pack BP2S00
Feature Highlights
TopView
Controls and Indicators
EXTERNAL When using an optional External Speaker
CONNECTOR
leD DltpIIy
FrontView
0000000 0000000 0000000 0000000 0000000
SCANKay
out a channel will not erase the programmed frequency
SCAN KEY
1 E~j E
@ @4
~7 I ~
~,,~
Channel Bank Channel
Bank
NUMERIC KEYPAD
1 - 2011 201 21 - 4012 221 41 - 6013 241 61 - 8014 261 81 -100 15 281
EENKey
j ~if ~
LMTLIntKV
SIPSlepKey
the selected channel, press E again
frequency. To store the same frequency into
selected steps are erased when you turn off the power
LCD Display
P 8 8 8 18 8 8. 8 8 8 8 MHz
HOLD UO WX 1 2 . 50KHz AM NFM WFM IKEYLOCKI
Installing the Battery Pack
Setup
Charging the Battery Pack
1. Turn the On-OffNolume Control OFF
Mounting the Flexible Antenna
Installing the Belt Clip
the unit while the battery is charging
3. Adjust the volume to a comfortable listening level
Scanning Overview
Note When squelch is open, you can hear the broadcast
noise, if no signal is present The scanner will not scan
A. Programming By Manual Entry
Programming Channels
4 6 0 . 1 5
4. Then, press MANUAL
selected channel, skip to Step
B. ProgrammingWith the Rotary Tuner
open empty channel, skip to Step
To program a channel using the Rotary Tuner
If the selected channel is open empty
If the selected channel already has a stored frequency
STPone time foreach selection 5 kHz, 12.5 kHz
~ramming With SEARCH
25 kHz, or 50 kHz, or press . twice to reset to default
ress MANUAL to stop scanning
The Auto Store feature automatically stores all active
D. Programming With AUTO STORE
errortones are emitted and Error appears on
12.5 kHz, 25 kHz, or 50 kHz, or press . twice to reset to default
~nother Open Channel
Transferring a Programmed Frequency to
Note If the selected bank is full, that is, all
display. In this case, select another bank
To delete a frequency from a channel
Deleting a Stored Frequency
1. Display the channel and frequency that is to be deleted
3. Press E The current channel is erased, and the display shows
Note You do not skip a locked out UG? channel using any of these keys
Scann ing
To directly access a specific channel 1. Press MANUAL
3. Press MANUAL again
Note Currently the Weather Service is not available in Australia
Weather Channel Scanning
Setting the Delay Mode
Setting the Scanning Speed
Setting the LCD Display Light
Customizing Scanner Operation
To restore all locked out channels of a selected bank at one time
To restore a locked out channel
described shortly in IISettingUpPriorityChannels
Channel Lock Out
To set up a Priority Channel
Setting Up Priority Channels
1. FIrstprogram your most important frequency into a bank channel
2. Press and hold PAl for more than 2.5 seconds
To activate the Count feature
Using COUNT to Monitor Channel Activity
2. Press MANUAL to stop scanning
To replace the Battery Pack
Care and Maintenance
2. Remove the Battery Pack by pressing in and slidingit down and off
yourunit
Do not use the scanner in high-moistureenvironments
Disconnectthe powertothe unitbefore cleaning
Cleaning
Clean the outside of the scanner with a mild detergent
PROBLEM
Troubleshooting
SOLUTION
Banks
Technical Specifications
WARRANTY
UBUEO1230DZ
unid~n~GP
Printed in the Philippines
@ 1994 Uniden Australia Pty. Limited. All rights reserved