=adjust maximum pressure valve B to the working value (in any case less than the safe maximum pressure the system can reach).

Pressure regulators with a volumetric valve (GCP ELETTRICO) Adjusting the maximum pressure valve

=put main control A in the drain position (“OFF”).

=loosen the hand wheel of maximum pressure valve B completely (anticlockwise).

=open volumetric valve E completely.

=start the pump by activating the power-takeoff of the tractor at 540rpm

=open main control A (position “ON”), the manometer will be activated

=open the drain tap on filter F slightly (only GCP ELETTRICO).

=close volumetric valve E completely. If the pressure rises over the maximum limit of the system, make sure maximum pressure valve B is open (see previous indications)

=open all of the section valves C (position “ON”)

=adjust maximum pressure valve B to a value over that of the working pressure (generally 10-14bar) and in any case lower than the safe maximum pressure that the system can reach.

Adjusting the volumetric pressure.

=with the volumetric pressure valve E adjust the pressure to the value the treatment will be done at (the pressure is indicated on the nozzles tables on the basis of the tractor speed and litres/hectare to spray)

Warning! The working pressure must be adjusted with the volumetric valve and not with the maximum pressure valve. In the case the working pressure is too near to the calibrated pressure of the maximum pressure valve, the proportional valve may not be able to compensate the speed variations correctly.

Adjusting the compensated returns

=close only one tap of section C (position “OFF”).

=adjust the corresponding compensator G until you return to the pressure set previously (displayed on the manometer).

=open and close the tap of section C and check that the pressure remains constant.

=repeat the above operations for all the section taps.

If the types of nozzles aren’t changed the regulations carried out will guarantee a constant spraying of the liquid also per treatments that are done at different working pressures.

NB: if the type of nozzle is changed then the calibrating will have to be done again.

4.8.3 DELIVERY FILTERS (ONLY EQUIPPED MODELS)

This is particularly useful when using small nozzles (low volume), they are normally mounted on the jet booms and have a filter cartridge with a 40-gauge mesh (the equivalent of a 0.4 mm hole).

At the end of each treatment cycle you should clean the cartridge: turn the jets to the closed position, put the command under pressure and open the tap under the filter to drain the tank for a few minutes.

You should clean the cartridge by hand periodically, on the basis of the product used. Stop the pump to clean. Wear rubber gloves and the other personal protective equipment when cleaning.

4.9AUXILIARIES TAPS BLOCK

A collector is installed (FIG. 9) in the machines with taps for the utilities and accessories, which require a working pressure that is independent from the spraying pressure:

-Tank washing jet: see paragraph 4.13.1

-Ejector: see paragraph 4.10

-Agitators (2 independent taps): see paragraph 4.12

The taps are identified by the relevant sticker and the methods of use are described in the paragraphs indicated.

The pressure is normally regulated to 30-35 bar with the relevant valve (using a yellow knob) and displayed on the manometer installed; opening the utilities makes the pressure drop.

FIG. 9

Tank rinsing

Ejector

Agitator 1

Agitator 2

unigreen 13

Page 13
Image 13
Unigreen P500, P600, P300, P400 Delivery Filters only Equipped Models, Auxiliaries Taps Block, Tank rinsing Ejector Agitator

P400, P300, P500, P600 specifications

Unigreen is a leading manufacturer in the agricultural machinery sector, known for its innovative solutions that meet the growing demands of modern farming. Among its impressive lineup, the Unigreen P400, P300, P600, and P500 series have garnered attention for their advanced features, cutting-edge technologies, and exceptional performance.

The Unigreen P400 is a versatile sprayer suitable for medium to large-sized farms. One of its key features is the high-capacity tank that minimizes the need for frequent refills, allowing farmers to cover substantial areas in a single pass. The sprayer is equipped with advanced precision technology that ensures uniform application of chemicals, which is crucial for maximizing crop yield while minimizing waste.

On the other hand, the Unigreen P300 is designed for smaller operations but does not compromise on performance. It boasts a compact design that makes it easy to maneuver in tight spaces. Its lightweight construction facilitates transport, and it incorporates user-friendly controls that enhance the operational experience for farmers. The P300's efficient spraying system reduces drift, ensuring that chemicals are applied exactly where needed, thus protecting the surrounding environment.

Moving onto the P600 model, this sprayer is engineered for large-scale agricultural operations. It features an extensive range of customizable options that cater to specific farming needs. The P600's robust build is complemented by powerful engines that ensure reliability even in demanding conditions. Additionally, it incorporates state-of-the-art GPS and automated guidance systems, allowing for precise inter-row spraying and reducing overlap—this significantly improves efficiency and decreases operational costs.

Lastly, the Unigreen P500 bridges the gap between the P400 and P600, offering advanced technology in a slightly smaller package. One of its standout characteristics is the innovative boom design that provides exceptional stability in various terrains. The sprayer includes advanced monitoring systems that track performance metrics in real-time, enabling farmers to make informed decisions while in the field.

Overall, the Unigreen P series sprayers are distinguished by their user-centric designs, technological advancements, and high-performance capabilities. Their commitment to sustainability and efficiency makes them an excellent investment for progressive farming operations looking to enhance productivity and optimize resource use. Unigreen continues to innovate, ensuring that their products remain at the forefront of agricultural technology.