3.
Press and release one of the MACRO keys. This will
be the key that will play back the series of key- strokes assigned to that key.
4.Begin entering the sequence of keystrokes, up to 15, that you wish to be played back when you press the MACRO key. For example:
RCVR – POWER – TV – POWER – TV/VCR (To change the input on the TV to VIDEO 1) – CBL/SAT
– POWER.
5.
Once your sequence is entered, press and hold SETUP until the Cinema 7+™ ’s red light blinks twice.
Now, using the example as above, whenever the pro- grammed MACRO key is pressed, the Receiver would power ON, the TV will power ON and change the input to VIDEO 1 and then the Satellite would power ON.
Repeat steps 1 - 5 to then setup a second sequence on the MACRO2 key.
VOLUME LOCK
Volume Lock allows the user to designate which component will control the volume in the TV, DVD/LD and CBL/SAT modes. To set the Volume Lock to the TV mode:
1. 
Press and hold SETUP until the Cinema 7’s red light blinks twice, then release SETUP.
2.
Press 9 - 9 - 3. The Cinema 7+™ ’s red light will blink twice.
3.
Press and release TV. The Cinema 7+™ ’s red light will blink twice.
Now, whenever you press VOL ▲ , VOL ▲ or MUTE in the VCR, DVD/LD and CBL/SAT modes your TV will control the volume. If you would like to change the Volume Lock setting to the VCR, DVD/LD or CBL/SAT modes repeat steps
You can also change the Volume Lock setting so that an Audio component controls the volume in all device modes.
To change the Volume Lock setting on the Cinema 7+™ to the RCVR or AUX mode:
1.
Press and hold SETUP until the Cinema 7+™ ’s red light blinks twice, then release SETUP.
2.
Press 9 - 9 - 3. The Cinema 7+™ ’s red light will blink twice.
3.
Press and release RCVR or AUX. The Cinema
or 7+™’s red light will blink twice.
Now, whenever you press VOL ▲, VOL ▲or MUTE your Audio component will control the volume in all device modes.
Web Site : http://www.oneforall.com
You can also change the Volume Lock setting so that each component controls its own volume. However, some compo- nents do not have volume control. Using this setting may eliminate volume control in some device modes. To change the Volume Lock setting on the Cinema 7+™ so each mode controls its own volume:
1.
Press and hold SETUP until the Cinema 7+™ ’s red light blinks twice, then release SETUP.
2.
Press 9 - 9 - 3. The Cinema 7+™ ’s red light will blink twice.
3. 
Press and release VOL ▲ . The Cinema 7+™ ’s red light will blink twice.
Now, whenever you press press VOL ▲, VOL ▲or MUTE on the Cinema 7+™ each component will control its own vol- ume, provided each component has volume control.
USING THE SLEEP KEY
The SLEEP key allows you to access the sleep timer of your TV, Cable Converter/DBS Satellite or Audio component. You can access your TV, Cable Converter, DBS Satellite or Audio component’s Sleep Timer by pressing the SLEEP key. Most Sleep Timers advance in increments of 10 or 15 minutes, however, for specific instructions on setting your components Sleep Timer, please consult your original owner’s manual.
Even if your original Cable Converter remote control did not have a sleep timer, your Cinema 7+™ has its own
1. Press and release the CBL/SAT key then press the SLEEP key once to set the Cinema 7+™ ’s
sleep timer for 15 minutes. The red light will blink once.
2. 
Each additional press of the SLEEP key will add 15 more minutes to the Sleep Timer, up to a maximum of 60 minutes. The LED will blink twice when the sleep timer is set for 30 minutes, 3 times for 45 min- utes, or 4 times for 60 minutes.
NOTE: The sleep timer starts 10 seconds after
the last press of the SLEEP key. Once you have activated the Cinema 7+™’s
3.
To
NOTE: Plugging your TV into the outlet on the back of the Cable Converter may allow you to turn both your Cable Converter and TV ON and OFF
Web Site : http://www.oneforall.com
28 | 29 |
