To Remove
Outer Ring, Cut
Here (6 Places)
Flue Opening
Restrictor
Plate
Sheet Metal
Screws
DVT44IN (6³⁄₄” as Shown) Use tin snips to cut along slots to make 4¹⁄₂” (114mm) restrictor plate. (Refer to Page 17)
Chateau™
Ceramic Refractory Installation
The ceramic refractories are fragile and should be handled with care. Due to the size of the refractories, an assistant may be helpful.
NOTE: The ceramic refractories are shipped sepa- rate from the unit but MUST BE installed.
Refer to Ceramic Refractory Kit listed below.
Appliance | Kit Model | Description |
DVT38 | DVT38CRR | Colonial Red |
DVT38 | DVT38CRL | Limestone |
DVT38 | DVT38CRH | Herringbone |
DVT44 | DVT44CRR | Colonial Red |
DVT38 | DVT38 |
Use tin snips to cut | Use tin snips to cut along |
along inner slots to | outer slots to make 4¹⁄₂” |
make 3” restrictor | (114 mm) restrictor plate. |
plate. (Refer to | (Refer to Page 22, Fig. 28) |
Page 17) |
|
FP1810 |
|
Fig. 36 Restrictor plate location.
Remove Screws (3)
Rear Log
Bracket
FP1556
Fig. 37 Remove rear log bracket.
| Fresh Air |
| Restrictor |
1 | Plate |
2 | |
3 |
|
4 |
FP1557
Fig. 38 Fresh air restrictor plate adjustment.
6.Replace the rear lower and upper refractory, side refractory, fettle, andiron, logs and glass.
DVT44 | DVT44CRL | Limestone |
DVT44 | DVT44CRH | Herringbone |
Left Side | Rear Refractory | Right Side | ||||||||||||||||||||||||||||||||||||
Refractory | ||||||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
| Upper | Refractory | |||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FP1365a | Rear Brick Lower |
| (Colonial Red Only) |
Fig. 39 DVT44IN ceramic refractory panels. (Limestone refractory shown)
1.Using a Phillips or Robertson screwdriver, unfasten the two (2) screws holding the fettle to the burner assembly. With a wrench, remove the front burner tube by unfastening the two (2) nuts that secure the burner tube to the front of the burner assembly.
2.Using a Phillips or Robertson screwdriver, remove the heat shield located toward the front top of the fire box by unfastening the five (5) screws that secure the heat shield in place. (Fig. 40)
| Return Flange |
| Remove |
| Screws (5) |
| FP1369 |
Fig. 40 | Remove five (5) screws securing heat shield in place. |
20011956 | 27 |
