Vermont Castings EWF30

Penetrating the Roof

Run pipe to roofline. Since chimney system must be vented to the out-of-doors, you must use an approved CFM Corporation termination.

If a chase is used, refer to the installation manual pro- vided with the termination cap.

Locate Chimney Centerpoint on Roof

Use same procedure detailed in locating center point of the flue system.

Drive a nail up through roof at the center point. This will determine center point on outside of the roof.

Cut and Frame Roof Hole

Size of roof hole varies with the type of chimney ter- mination installed. Refer to installation instructions provided with CFM Corporation chimney termination to find correct size of roof hole.

There must be a 1¹⁄₂” (38 mm) air space between out- ermost portion of chimney sections and any adjacent combustible surfaces. (Combustible surfaces include burnable materials such as: ceiling members, joists, flooring, combustible insulation and roof structures.)

WARNING: Do not pack required air spaces with insulation or other materials.

Mark an outline of the roof hole around the center of the point nail. NOTE: Hole dimensions given in the chim- ney top installation instructions are horizontal dimen- sions; therefore, the hole size must be marked on the roof accordingly.

CAUTION: Treatment of firestop spacers and construc- tion of chase may vary with type of building. These instructions are not a substitute for local building codes. You must check your local building codes to determine specific requirements for your city or state. NOTE: Other building materials may be required in addition to CFM Corporation Firestop Spacers.

Finishing

CAUTION: All joints between the finished wall and the fireplace surround (steel front) must be sealed with noncombustible material to prevent cold air leakage into the room. (Fig. 20, 21)

NOTE: No material may cover black cast face.

Air Space Clearances

Combustible framing material MUST NOT penetrate AIR SPACE (shaded areas)

1¹⁄₂

 

(38 mm)

Standoff

 

1” (25 mm) Air Space to Sides

Firestop

Cover the opening of the installed chimney so debris cannot get into the system.

Cut and frame the hole. It is good practice to use fram- ing lumber that is the same size as the rafters. Install the frame securely because the chimney top and flash- ing anchored to the frame must be able to withstand heavy winds.

Install Remainder of Chimney Sections

Since you have already preplanned the height of your termination according to the Ten Foot Rule, continue to

Wall

Shield

NO material may cover cast face

1” (25 mm) Space to Back

1” (25 mm) Air Space to Sides

install pipe to the predetermined height.

Check the chimney top installation instructions for details on how high above the roof top the chimney sec- tions (all pipes) should extend.

Install Top Housing or Termination

Follow the installation instructions provided with the chimney termination you have selected.

Installing Chimney in a Chase

Refer to Figure 2, Page 5 for an illustration of a typical chase installation.

Hearth Extension

0” Clearance

to Floor

 

FP1567

Fig. 20 Minimum clearances to combustibles.

Finish Wall

Finish the wall with material of your choice. Do not install a combustible mantel shelf less than 12” (305 mm) above the firebox grille opening. Do not install a mantel face plate less than 6” (159 mm) from top of grille opening. (Fig. 22) If a combustible material is used below a flat mantel shelf, consult your

14

20008662

Page 14
Image 14
Vermont Casting EWF30 Penetrating the Roof, Locate Chimney Centerpoint on Roof, Cut and Frame Roof Hole, Finishing

EWF30 specifications

The Vermont Casting EWF30 is a testament to innovation and craftsmanship in the world of cast iron wood stoves. This highly efficient wood-burning stove combines traditional aesthetics with modern technology, making it a perfect centerpiece for both rustic and contemporary homes. One of the standout features of the EWF30 is its impressive heating capacity. Designed to heat areas up to 2,000 square feet, it is ideal for large spaces, providing consistent warmth during chilly months.

Constructed from high-quality cast iron, the EWF30 offers a durability that only improves with age. This material is known for its excellent heat retention and distribution, resulting in a steady, comfortable warmth. The stove’s classic design includes large ceramic glass windows, allowing users to enjoy the mesmerizing beauty of the fire while safely keeping the warmth inside.

Incorporating advanced technology, the Vermont Casting EWF30 features a clean burning system that significantly reduces emissions. This is a critical aspect for environmentally conscious consumers, as the stove adheres to strict EPA standards, promoting cleaner air and reduced environmental impact. The efficiency of this wood stove is exceptional, with a thermal efficiency rating that maximizes heat output while minimizing fuel usage.

The EWF30 is equipped with a user-friendly air control system, allowing for easy adjustments to the airflow. This system enhances the combustion process, enabling users to achieve the desired flame and heat levels effortlessly. The top-loading design also simplifies the refueling process, making it easier to add wood without disturbing the existing fire.

Aesthetically, the Vermont Casting EWF30 can be customized with various finishes, including traditional black, enamel, and even bold colors, ensuring it fits seamlessly with any interior decor. Additionally, this model includes a removable ash pan, providing a convenient cleaning option.

In summary, the Vermont Casting EWF30 is more than just a wood stove; it is a fusion of tradition and technology. Its heating efficiency, durability, and aesthetic appeal make it a worthy investment for anyone seeking a reliable and stylish heating solution for their home. Whether for ambiance or functionality, the EWF30 is designed to enhance the living experience while respecting the environment.