Installation Instructions
General
1.Read all instructions before using this appliance.
2.This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this appliance. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and cur- tains at least 3 feet (914mm) from the front of this appli- ance.
3.CAUTION: Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating unattended.
4.If possible always unplug this appliance when not in use.
5.Do not operate any heater with a damaged cord or plug or after the appliance malfunctions, has been dropped or damaged in any manner.
6.Any repairs to this appliance should be carried out by a qualified service person.
7.Under no circumstances should this appliance be modified. Parts having to be removed for servicing must be replaced prior to operating this stove again.
8.Do not use outdoors.
9.This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate this appli- ance where it may fall into a bathtub or other water contain- er.
10.Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic areas and where it will not be tripped over.
11.To disconnect this appliance, turn controls to the off posi- tion, then remove plug from outlet.
12.Connect to properly grounded outlets only.
13.This appliance, when installed must be electrically ground- ed in accordance with local codes, with the current CSA C22.1 Canadian Electrical codes or for USA installations, follow local codes and the National Electric Code, ANSI/NFPA No. 70.
14.Do not insert or allow foreign objects to enter any ventila- tion or exhaust opening as this may cause an electric shock, fire or damage the appliance.
15.To prevent possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
16.This appliance has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. This appliance should not be used as a drying rack for clothing, nor should Christmas stockings or decorations be hung on or near it.
17.Use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons.
18.Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be 14 ga min-
imum size and rated not less than 2025 Watts. The exten- sion cord must be a three wire cord with grounding type plug and cord connector. The extension cord shall not be more than 20 feet (6m) in length.
Locating Your Fireplace
Your new fireplace may be installed in a prefabricated cabinet available from your dealer.
When choosing a location for your new fireplace, ensure the general instructions are followed. Also, for best effect install the fireplace out of direct sunlight.
Clearance to Combustibles
Sides . . . . . . . . . . . . . . . . . . . 0” (0 mm)
Floor . . . . . . . . . . . . . . . . . . . .0” (0 mm)
Top . . . . . . . . . . . . . . . . . . . . .0” (0 mm)
Cabinet Installations
Cabinets are available from your dealer which allow for fast, convenient installation of your fireplace against existing walls.
For instructions on handling and assembly of your cabinet, refer to separate installation instructions that come with the cabinet.
If it is necessary to secure your fireplace into a cabinet (i.e. VCEF26RV) such as for installations in a recreational vehicle, the fireplace may be secured by this method (hardware not supplied):
Remove the glass door from the unit and set aside. 3/16” (5
mm)clearance holes, two (2) per side must be drilled through the fireplace sides for #8 x 3/4” long black oxide wood screws or similar. The mounting holes can be located on left and right sides approximately 2” (51 mm) from the top and 5” (127 mm) from the bottom of the glass door area. The mounting hole location distance from the front of the unit must not interfere with the glass door and the refractory (brick pattern) when rein- stalled. If necessary, modify the cabinet for the mounting screws to attach. Double check the mounting hole’s locations on the fireplace before drilling. A small 1/16” (2 mm) pilot hole or center punch before drilling is recommended. Mark and drill from the outside to avoid marking or damaging the interior of the fireplace. Tighten the screws evenly so the unit remains centered in the opening and without distorting the sides of the fireplace unit. It is advisable to place wood shims or similar between the fireplace sides and the cabinet to prevent distor- tion when tightening the screws. 1/2” (13 mm) Velcro strips for securing the log to the grate tines and away from the screen are recommended.
SAVE THESE INSTRUCTIONS
10007176 | 3 |
