Replacing the Light Bulbs

Depending on your model, the fireplace uses two (2) or three (3) clear 120 Volt, 60 Watt, E-12 socket base light bulbs (small base, chandelier candle type). The lights are located under the ember bed of the unit. For convenience, if one of the light bulbs burns out, it may be easier to replace all of the light bulbs at the same time.

Do not exceed 60 Watts per bulb. Use of higher rated bulbs may result in a fire, causing property damage, personal injury or loss of life.

1.Turn off power to the unit.

2.Let fireplace cool if it has been operating.

3.Remove fixed front panel, or open doors (depend- ing on model).

4.Locate two (2) screws that hold the refractory (brick patterned) bracket together with the ember bed. (Fig. 5)

5.Remove those two (2) screws using an appropriate screwdriver. One screw is located on either side of the unit.

Remove Screws

Fig. 5 Remove screws that hold refractory bracket with ember bed.

6.Pull the ember bed out of the unit, by gently pulling towards you and only slightly upwards. Depending on the model, you can remove the refractory prior to removing the ember bed.

Pull Here (both sides)

Fig. 6 Pull ember bed out of unit.

7.Looking into the opening of the unit under the ember bed, visually locate the light bulbs.

8.Remove the light bulbs by unscrewing them out of the bases, turning them counterclockwise. You can use one hand to hold the light socket in place, if required.

9.Install the new light bulb(s) by turning the light bulb into the base clockwise. You can use one hand to hold the light socket in place, if required.

60 W Light Bulbs

Fig. 7 Remove and replace light bulb(s).

10.Reposition the ember bed. If required, gently raise the refractory panels, one at a time, to tuck the ember bed edge underneath them.

11.Reposition the refractory bracket, aligning the refractory in place as required.

12.Replace two (2) screws taken out in Step 5, by using an appropriate screwdriver.

Maintenance of Motors

The motors used on the fan and the drum assembly are prelubricated for extended bearing life and require no further lubrication. However, periodic cleaning/vacu- uming of the fan/heater is recommended.

Make sure the power is turned OFF before proceeding.

Cleaning

Cleaning of the touchpad label at the bottom front of the unit is to be done only using a soft cloth, slightly dampened in water (if needed, a small amount of dish soap can be added to the water) and dried using a clean, dry soft cloth. DO NOT use any abrasive house- hold cleaners as these products will damage the touchpad controls.

7

10007176

Page 6 Page 8
Page 7
Image 7
Vermont Casting VCEF26, VCEF33, VCEF36 installation instructions Replacing the Light Bulbs, Maintenance of Motors, Cleaning
Page 6 Page 8

VCEF33, VCEF36, VCEF26 specifications

Vermont Castings is renowned for its commitment to quality and craftsmanship, particularly evident in its line of cast iron gas fireplaces, including the VCEF26, VCEF36, and VCEF33 models. Each of these units reflects a dedication to performance, efficiency, and aesthetic appeal, making them ideal choices for heating modern homes.

The VCEF26 is a compact yet powerful fireplace that is perfect for smaller spaces. Its design is optimized for efficient heating, featuring an impressive heat output while maintaining a low profile. With the ability to produce up to 26,000 BTUs, the VCEF26 warms your living area effectively without overpowering the space. One notable feature of this model is its embedded ceramic glass that offers a stunning view of the flames while ensuring safety and efficiency. The adjustable flame height enhances ambiance and accommodates different heating needs.

Moving on to the VCEF36, this fireplace is a versatile choice for larger rooms. With a heat output of up to 36,000 BTUs, it ensures that ample warmth reaches every corner of your space. The VCEF36 also boasts Vermont Castings' advanced burner technology, which promotes an even flame spread and improves fuel efficiency. Additionally, this model comes with customizable features, including various trim options and a choice of decorative media, allowing homeowners to tailor the look of their fireplace to suit their individual styles.

The VCEF33 offers a middle-ground option, combining the features of the VCEF26 and VCEF36. With a heat output of 33,000 BTUs, this model is designed to meet the needs of medium to large rooms. Its innovative design includes an easy-to-use remote control for convenient operation, allowing users to adjust the flame and heat settings with the touch of a button. The VCEF33 also implements a direct venting system, ensuring clean and efficient combustion while minimizing the impact on indoor air quality.

All three models harness the benefits of Vermont Castings' commitment to environmental responsibility. Each unit complies with stringent EPA standards for emissions, reflecting the company’s pledge to sustainability. The cast iron construction not only provides durability but also retains heat effectively, contributing to their overall efficiency.

In summary, the Vermont Castings VCEF26, VCEF36, and VCEF33 gas fireplaces stand out for their combination of aesthetic appeal, performance, and energy efficiency. With versatile designs and advanced technologies, they cater to a wide range of heating needs, ensuring comfort and style for any home.
Top Page Image Contents