Operating Instructions
All of the fireplace control functions can be accessed in two (2) ways:
•Using a multifunction remote control unit
•Using touchpad control panel, located in the lower
Remote control unit has all the controls required to operate any feature on the unit. If you prefer to use the touchpad control on the fireplace unit itself, open the fixed front or open the doors (depending on the model) to access the touchpad buttons. The layout of the but- tons on touchpad and remote control unit can be seen in Figures 8 & 9, respectively.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3 |
|
|
|
|
|
|
|
|
|
|
| |||
R |
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| A |
|
|
|
|
|
|
| ||||||||
6 |
|
| |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| 5 |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| 4 |
|
|
| ||||
|
|
| 1 |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| LED |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fig. 8 Touchpad buttons. |
|
|
|
|
|
|
|
| |||||||||
•As a visual effect - only flame effect is on, the heater is off. We recommend this mode for warm weather application, when you want the ambiance of a fire, without any heat output.
•As a heater - only heater is on, while the flame effect is off. this mode allows you to use your fireplace as an electric heater, without any flame effect.
Refer to Figure 8 & 9 for locations of the buttons on both, the touchpad and remote control unit, described in the following operating instructions. Note that in both cases, button numbers as shown in the figures are the same.
Flame Speed Control
Your fireplace features a flame speed control. By depressing button 1 once you will activate the flame effect. If this is the first time you use this unit, the visu- al indicator of the flame effect (A) will be lit up to about half its height. By repeatedly depressing buttons 2 and 3, you can respectively decrease or increase the flame effect speed to achieve desired flame effect. Refer to visual indicator A to monitor relative speed of the flame effect between the slowest (indicator A showing only one light) and fastest (indicator A showing all lights lit up) setting. For added convenience, control board in your fireplace will remember your last setting on sub- sequent activation.
3
1 
2
Heater Control
Your fireplace features a variable temperature setting control. By depressing button 4 once, you will have activated the heater. To change the comfort level in the
4 | 5 |
ON/OFF 
6
Turns unit OFF and starts BOTH functions at remembered setting.
Fig. 9 Remote control.
The fireplace features conveniently separate controls for flame effect and for heater control. This allows you to operate the unit in three (3) different modes:
•As a
room, you can repeatedly depress buttons 5 and 6 to decrease or increase the temperature setting, respec- tively (for example, by repeatedly depressing button 6, you will increase the temperature setting and your room will feel warmer). To achieve the desired effect, refer to visual indicator R, as your guide on the level of the heat output.
NOTE: During each operation of this unit, the unit fea- tures will initiate the LED, a visual indicator of flame effect (A), and a visual indicator of the heat output (R). The LED and all visual indicators will automatically turn off after 20 seconds.
10007176 | 9 |
