Vestax PMC-CX owner manual MIC / Line Section, Rear Panel Monitor Section

MIC / LINE SECTION

29

30

31

@9SUB MIC LEVEL VOLUME

Adjusts the input level of the SUB MIC input.

#0MAIN MIC / SUB LINE SELECTOR

Selects between MAIN MIC and SUB LINE input.

#1MIC / LINE EQ VOLUME

Adjusts the HI and LOW frequencies for the signal chosen by MAIN MIC / SUB LINE SELECTOR.

#2MIC / LINE LEVEL VOLUME

Adjusts the input level of the MAIN MIC or SUB LINE input.

#3MIC / LINE CUE SWITCH

HOW TO CHANGE THE FADER UNIT

REAR PANEL

49	50	46	45	44		39
51
						38
52
48	47	43		42	41	40

32

33

MONITOR SECTION

34

35

36

Sends the signal from the MIC or LINE channel to the monitor section for headphone monitoring. When switch is on, an indicator lights up.

#4SPLIT / STEREO SELECTOR

When this switch is set to "SPLIT", the master signal is always heard through the right ear-cup of the headphone. The signal selected by each CUE SWITCH will be heard in the left ear-cup. This enables both programs to be monitored simultaneously, thus assisting in beat mixing. When this switch is set to "STEREO" no master output is heard in the headphones, and only the signal selected by each CUE SWITCH will be heard in both ear-cups.

#5HEADPHONE EQ VOLUME

Adjusts the HI and LOW frequencies for Headphone monitoring.

#6HEADPHONE LEVEL VOLUME

#8MAIN/SUB MIC JACK

[MAIN MIC: XLR JACK (BALANCED), SUB MIC: PHONE JACK (UNBALANCED)]

Input jack for MIC.

#9LINE INPUT JACK

[LINE: RCA PIN JACK, SUB LINE: 1/4' PHONE JACK (UNBALANCED)]

Input connectors for line level equipment such as CD players, CD-R/RW players, MD players, tape decks, DVD players, DAT and VTR etc.

$0PHONO INPUT JACK [RCA PIN JACK]

Input jacks for turntables. Connect turntables equipped with MM (pick up) cartridge.

$1GND TERMINAL

Connect this terminal to the ground lead of the turntable. This will help to reduce unnecessary noise.

$2INPUT LEVEL SELECT SWITCH[-10/0dB]

Select the attenuation level for the input.

$3BOOTH OUT JACK

[1/4' PHONE JACK (UNBALANCED), XLR JACK (BALANCED)]

Connects to the DJ booth monitors. This signal is identical to the HEADPHONE OUT signal.

$7MASTER OUT 1/2 JACK

[1/4' PHONE JACK (UNBALANCED), XLR JACK (BALANCED]

Connect to the input on a power amplifier. These jacks are Phone type for consumer applications. This mixer has two sets of MASTER OUT jacks so that the each output level can be set separately. Therefore, the MASTER OUT can be used for main output or sub output IE. One for the main area and the other for entrance.

$8MASTER OUT LEVEL SELECT SWITCH [-10/0dB]

Select the attenuation level for the BOOTH OUT.

$9MASTER LOOP SEND JACK [1/4' PHONE JACK]

Connects the input terminal of an external effector. (Delay, Reverb, etc.)

%0MASTER LOOP RCV JACK [1/4' PHONE JACK]

Connects the output terminal of an external effector.

%1POWER SWITCH

Power on/off.

%2AC IN JACK

Connect the Vestax AC-20 , AC adaptor.

37

Adjusts the headphone monitor level.

#7PHONES JACK

Use this jack to connect headphones. Headphones with an impedance of 8ohm to 600ohm can be used on this unit.

*For best sound quality Vestax recommends using Headphones with 150ohm impedance.

$4BOOTH OUT LEVEL SELECT SWITCH

Select the attenuation level for the BOOTH OUT.

$5MIC MONITOR IN/OUT SWITCH

Select whether the signal connected to MAIN/SUB MIC is mixed with the signal outputted from MASTER OUT1/2.

$6REC OUT JACK [RCA PIN JACK]

Connects to the input jack of a recording device IE, tape recorder, MD, DAT, etc. The output level of this jack is fixed and does not change with the MASTER LEVEL.

8 9