Vidikron v120 5.2 Filter Replacement

Maintenance and Troubleshooting

64 Vidikron Vision Model 120 Owner’s Operating Manual

PRELIMINARY

6. Install the new lamp module.

7. Replace the lamp cover and re-tighten all screws.

5.2 Filter Replacement

Whenever you replace the lamp – or more often if the projector is installed in an extremely

dusty environment – you should also replace the filter located at the right side of the

projector.

1. Loosen the two screws holding the

filter access panel in place. Then,

remove the panel.

2. Pull the filter out of the projector

and discard. Do not reuse filters.

3. Insert the new filter with the pleats

facing in and the foam-covered side

facing out.

4. Replace the filter access panel and

tighten the screws to secure it.

Side Filter

Access

Panel

Contents

Main Page TWO YEAR LIMITED WARRANTY For Projectors, Video Processors and Controllers Page VIDIKRON PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS Safety Precautions Page Page Page Page Page Page 1.1 About This Manual 1.2 Using This Manual WARNING DANGER! 1.3 Description, Features and Benefits Page 2.1 Vision 120 at a Glance 2. Controls and Functions 2.2 Vision 120 Rear Panel Page 2.3 VHD Controller Front Panel Page 2.4 VHD Controller Rear Panel 123 4 5 67 8 9 Page Controls and Functions 12 Vidikron Vision Model 120 Owners Operating Manual 2.5 Vision 120 Remote Control Figure 2-5. Vision 120 Remote Control LIGHT OFF ON SOURCE PICTURE MEMORY ASPECT RATIO Page Page 3.1 Remote Control 3.2 Quick Setup Table 3-1. Installation Overview 3.3 Installation Considerations Table 3-2. Projector Installation Options Table 3-3. Vision 120 Lens Options and Throw Ratios Ceiling Installation Floor Installation Figure 3-4. Horizontal Lens Shift (EXAMPLE ONLY) Table 3-4. Vision 120 Vertical and Horizontal Lens Shift Limits 3.4 Installing the Primary Projection Lens Page 3.5 Installing the Optional CineWide Lens Mount Page Page Page Page Page 3.6 Mounting the Vision 120 3.7 Connections to the Vision 120 and VHD Controller Page Installation Vidikron Vision Model 120 Owners Operating Manual 33 Digital (DTV) RGB or Component Video Connections: See Figure 3-12 and Figure 3-13. Figure 3-12. Digital (DTV) RGB or Component Video Connections (HD1, HD2) Figure 3-13. Digital (DTV) RGB or Component Video Connections (HD3) Page Page to Automation/ Control System or PC Page Page 3.8 Turning on the Power 3.9 Adjusting the Picture Orientation V120 Component RCA 16:9 480I 3.10 Primary Lens Adjustments 3.11 Installing and Adjusting the CineWide Anamorphic Lens Page Page Page Page Wrong Position Correct Position Page Page Operation 50 Vidikron Vision Model 120 Owners Operating Manual Figure 4-1. VHD Controller OSD Menu Structure for Vision 120 Input Source Calibration ISF Presets Input Position 7 Table 4-1. Aspect Ratio Settings Table 4-1. Aspect Ratio Settings (continued) Page Page Page Page 7 Page Page Page Page 5.1 Lamp Replacement WARNING 5.2 Filter Replacement 5.3 Troubleshooting Tips Table 5-1. Troubleshooting Chart Page 6.1 RS-232 Connection and Port Configuration 6.2 Serial Command Syntax Table 6-1. Serial Commands and Responses Table 6-1. Serial Commands and Responses (continued) Page 7.1 Vision 120 Specifications Table 7-1 lists the Vision 120 specifications. Table 7-1. Vision 120 Specifications Table 7-1. Vision 120 Specifications (continued) 7.2 VHD Controller Specifications Table 7-2 lists the VHD Controller specifications. Table 7-2. VHD Controller Specifications Specifications 74 Vidikron Vision Model 120 Owners Operating Manual 7.3 Vision 120 Dimensions Figure 7-1 shows the Vision 120 dimensions (all dimensions are in inches). Figure 7-1. Vision 120/CineWide with AutoScope Dimensions