Vidikron VP-6000a, VP-4200a, VP-5000a manual Screen, To highlight Image Position

Operation

COLOR CHART

RED	:	+30
YELLOW	:	+30
GREEN	:	+30
CYAN	:	+30
BLUE	:	+30
MAGENTA	:	+30
C. CHART RESET
RETURN
SET ENTER	MENU	EXIT

Screen ➤

PLASMAVIEW			INPUT 1
PICTURE	SCREEN	SET-UP	OPTION
IMAGE POSITION		: 0 / 0
FREQ. ADJ.		: 0
PHASE. ADJ.		: 0
IMAGE RESET
SET SET		MENU	EXIT
INSTALLER ADJ.			INPUT 1
PICTURE	SCREEN	SET-UP	OPTION

H SHIFT	: +128
V SHIFT	: +128
FREQ. ADJ.	: +128
PHASE ADJ.	:	+4
H-SIZE	:	0
V-SIZE	:	0
IMAGE RESET
SET SET	MENU	EXIT

Color Chart (Installer Adjust mode): Select Color Chart from the Picture menu to adjust the

color density for each of the six primary colors: red, yellow, green, cyan, blue and magenta. Changing these settings for a primary color alters the hue of that color and affects the gamut (range) of possible colors. For example, changing the value for red moves the color closer to either yellow or magenta, which in turn affects all displayed colors having a red component.

To reset the color gamut settings to the factory default values, select C. Chart Reset. Then, press to highlight YES and press SET.

Select Return to exit the Color Chart menu.

Gamma (Installer Adjust mode): The Gamma control determines how gray shades are displayed between minimum input (black) and maximum input (white) for all signals. A good gamma setting helps to optimize blacks and whites while ensuring smooth transitions for the “in-between” values utilized in other grays.

Unlike brightness and contrast controls, Gamma allows you to lighten or darken the overall tone of your images without changing the extremes. All images will be more vibrant while still showing good detail in dark areas.

The default Gamma setting of 2.2 is appropriate for most typical home theater environments.

Factory: To reset all picture quality settings for the current input to the default, installer-adjusted values (or factory defaults, if in Installer Adjust mode), select Factory from the Picture menu. Then, press to highlight YES and press SET.

Image Position: Use the up- or down-arrow buttons (	, ) to highlight Image Position.
Then, press SET and use the left- and right-arrow buttons ( , ) to shift the image
horizontally; use the up- or down-arrow buttons ( ,	) to shift the image vertically.

V Shift (Installer Adjust mode): Use the up- or down-arrow buttons ( , ) to highlight V Shift. Then, press SET and use the right-arrow button ( ) to shift the image up; use the left-arrow button ( ) to shift the image down.

H Shift (Installer Adjust mode): Use the up- or down-arrow buttons ( , ) to highlight H Shift. Then, press SET and use the right-arrow button ( ) to shift the image to the right; use the left-arrow button ( ) to shift the image to the left.

Frequency Adjust (Input 1 only): Use the up- or down-arrow buttons ( , ) to highlight Freq. Adj. Then, press SET. The Frequency Adjust control adjusts the PlasmaView’s internal clock frequency in small increments to match that of the incoming signal. Use it to reduce or eliminate letter breakup, flickering or other “noise” in a computer screen image.

Phase Adjust (Input 1 only): Use the up- or down-arrow buttons ( , ) to highlight Phase Adj. Then, press SET. Use the Phase Adjust control to correct color misalignment or flickering text in a computer screen image.

Frequency Adjust and Phase Adjust are adjustable only when Auto Setup

Note Mode (in the Option menu, described later in this section) is set to OFF.

H-Size(Installer Adjust mode): Use the up- or down-arrow buttons ( , ) to highlight H-Size. Then, press SET and use the right-arrow button ( ) to increase the width; use the left-arrow button ( ) to decrease it.

38 Vidikron PlasmaView Owner’s Operating Manual