Viking F20725A TruProtect “Basic” Function “Quick” Reference, Function Access, Solid Door Models

Models: F20725A

1 12
Download 12 pages 13.25 Kb
Page 8
Image 8
SETTING THE CONTROLS

SETTING THE CONTROLS

The temperature of the refrigerated beverage center ranges from 40ºF to 65°F (4ºC to 18ºC).

TruProtect“Basic” Function “Quick” Reference

Solid Door Models:

 

55

˚F

 

WARMER

 

TruProtect System

ON

 

 

POWER FAILURE - Flashing Amber

SET

 

F/C

 

HIGH/LOW TEMP - Red

OFF

 

 

COLDER

 

 

 

 

 

ALARMS OFF - Steady Amber

PRESS AND HOLD

PRESS ON/OFF - Reset

 

Function

 

 

 

Function Access

 

 

 

 

 

Turn Unit On & Off

Pressing and holding the keypad OFFON for 5-seconds will turn the unit “ON” or “OFF”.

 

 

 

Adjust Temperature Set-Point

To adjust temperature set-point, touch SET keypad and current set-point will be displayed.

 

Use the WARMER or

COLDER keypads to adjust set-point temperature.

 

Display “Actual” Temperature

Display represents “real-time” monitoring of the compartments stored wine and/or

 

contents. Some temperature fluctuation around your desired set-point is normal.

 

 

 

 

Select ºF or ºC Display

Pressing the ˚̊F/C

keypad will toggle the display between Fahrenheit and Centigrade

 

temperature display.

 

Black-Out Mode

Display automatically shuts off when door is closed.

 

 

 

Display Lighting

Display Lighting can be enabled with the door closed by pressing the LIGHT keypad.

 

 

 

Sabbath Mode

Press and hold the SET keypad while pressing the ˚̊F/C keypad four (4) times.

 

 

 

TruProtect™ System

System monitoring is automatically enabled unless system has been disabled. (See

 

below.)

 

 

Door Ajar Alarm

For Door Ajar Alarm, TruProtect must be Enabled, (See “Disable/Enable TruProtect”,

 

described below.)

 

 

High/Low Temp Alarm

Note:

 

Alarm may occur when changing set-points in excess of 10ºF, and/or high usage,

 

 

this is normal. TruProtect must be Enabled, (See “Disable/Enable TruProtect”, described

 

below.)

 

 

Power Failure Alarm

Note:

Alarm will occur upon initial installation, since unit was run at factory to verify

 

 

quality, this is normal. TruProtect must be Enabled, (See “Disable/Enable TruProtect”,

 

described below.)

 

Reset Alarms

Close door to reset Door Ajar alarm. Press ON keypad to reset all other alarms.

Glass Door Models:

 

55

 

 

 

TruProtect System

 

 

WARMER

F/C

POWER FAILURE - Flashing Amber

ON

˚F

SET

˚̊

 

HIGH/LOW TEMP - Red

OFF

 

COLDER

LIGHT

 

 

ALARMS OFF - Steady Amber

PRESS AND HOLD

PRESS ON/OFF - Reset

 

Control Confirmation/Comment

Display will be blank TruProtect™ “Basic” Function “Quick” Reference when refrigeration sytem is off. Lights will still function, but will time-out 15 minutes after

each activation, if door is left open or display lighting is on, to prevent overheating.

“Set” will appear in display 55 ˚F when in set-point mode. “SET” mode will automatically time-out in 10 seconds if no

keypad activity occurs, or you may exit “SET” mode by pressing the SET keypad a second time.

Temperature variation in “compartment air”, above and below set-point, is a normal effect of refrigeration system cycling on and off. Stored items will not experience the full temperature swing of the compartment air due to the dampening effect of their thermal mass.

55

˚F

=

13

˚C

 

 

In addition, the control panel is hidden when door is closed.

Option available on Glass Door Models only.

Display will flash

SA

four (4) times, then unit will enter Sabbath Mode. The display, audible alarms, LED and lights will

be disabled. Sabbath Mode will automatically time-out in 36 hours, or can be exited by repeating the enable keypad routine.

LED displays steady green Solid Door Models: when TruProtect™ is enabled.

Audible alarm will sound 3-times every 30-seconds, LED will flash green. Function

Alarm will sound 6-times every minute and LED will flash red

if product temperature excursions occur for a duration

outside acceptable limits.

 

LED will flash amber Function Access whenever power is interrupted to unit. No audible signal.

Note that although pressing the ON keypad will reset the alarms, the alarm will resume if the “alarm condition” still

OFF

exists.

OFF

Disable/Enable TruProtect™

Press and hold the SET keypad for 5-seconds to “disable” or “enable” TruProtect™

 

System.

LED displays steady green Glass Door Models: when alarms enabled. LED displays steady amber Control Confirmation/Comment when disabled.

14

15

Page 8
Image 8
Viking F20725A manual TruProtect “Basic” Function “Quick” Reference, Function Access, Control Confirmation/Comment