Viking F21287A EN manual Vwho 18H. Outdoor Wall Hoods 36, 48, 182

Dimensions & Specifications

(VWHO 18”H. Outdoor Wall Hoods 36”, 48”, & 60”)

Clearance Dimensions

(VWHO 18”H. Outdoor Wall Hoods)

Seal joints with silicone.

Provided on “T” Series only.

	6”
	(15.
	2	cm)
	A (Hood width)		A
36”W.	35-7/8” (91.1 cm)
48“W.	47-7/8” (121.6 cm)
60”W.	59-7/8” (152.1 cm)

12”
(30.
5	cm)
18”
(45.
7	cm)

27”
	.6	cm)
(68

		18"
(45	.7	cm)

66"
(167 mín.
.
	6
acm)
72"	9máx
(182. .
	cm)

			“X”
DIM1/2"
+	4-		cm)
		.4
(11

27"
(68	.6	cm)

30"
2mín
(76.	.
acm)
36"
4máx.
(91.
	cm)

NOTE: Optional duct cover sold separately.

VWHO 18”H. Outdoor Wall Hoods

Description	36”	48”	60”
Duct cover width	35-7/8” (91.1 cm)	47-7/8” (121.6 cm)	59-7/8” (152.1 cm)
Duct cover depth		12” (30.5 cm)
Duct cover height		12” (30.5 cm)
Number of filters	2	3	4
Interior ventilator kits	VINV1200*	VINV1200*	VINV1200*
Exterior ventilator kits	DEV1200*/1500**	DEV1200*/1500**	DEV1200*/1500**
In-line ventilator kits	DIL1200	DIL1200	DIL1200
Interior duct size		10” (25.4 cm)
Exterior duct size		10” (25.4 cm)
Interior—Maximum amps	9.0	11.4	11.8
Exterior—Maximum amps	6.1/6.8	8.4/9.1	8.8/9.5
In-Line—Maximum amps	7.9	10.2	10.6

*A 1,200 CFM interior- or exterior-power ventilator should be used with all outdoor models and when indoor models are installed over range/rangetop with gas char-grill. Max duct run is 50 ft (15.2 m).

**It is recommended that the 1,500 CFM ventilator be used with longer duct runs. Max duct run is 75 ft (22.9 m). NOTE: Maximum amp rating for hoods includes recommended ventilator kit rating; All products must be hard wired with 2- wire with ground. An interior- or exterior-power ventilator kit must be purchased for installation with all 18”H. hoods.

36"
(91	.4	cm)

Note: Outdoor Models must be installed in a covered, non-enclosedarea, and should be protected from the elements as much as possible.

The bottom of the hood should be 30” (76.2 cm) to 36” (91.4 cm) above the grill surface. The hood should be installed 4-1/2” (11.4 cm) plus the distance between the back trim and surface from the back wall. (Note: There is a 3” minimum clearance from the back trim to non-combustible surfaces, and a 24” minimum to combustible surfaces.) This will require building the hood out from the wall. Any combustible material used for this purpose must be covered with locally-supplied stainless steel. Viking also recommends using a backsplash.

12 13