Troubleshooting
This Troubleshooting Chart is not prepared to replace the training required for a professional refrigeration service person, not is it comprehensive
Troubleshooting Chart
Complaint |
| Possible Causes |
|
| Response |
| ||
1.Unit not | a. | Power cord unplugged |
| a. | Check for power cord plug |
| ||
running | b. | No power to unit | ambient | b. | Check power at receptacle & fuses | |||
| c. | Setting higher than | c. | Lower temperature setting |
| |||
|
| temperature |
|
| Decrease the value as to 4 °F | |||
| d. | Differential too high |
| d. | ||||
| e. | Incorrect or loose wirings | e. | Check all wirings and connections | ||||
| f. | Low voltage |
| f. | Contact an authorized electrician | |||
| g. | Defrost light blinking |
| g. | Unit is under defrost mode |
| ||
| h. | Compressor light blinking | h. | Unit waits for | ||||
2.Fan running | a. | a. See 4) to set FON = 0 |
| |||||
continually |
| mode for humidity modulation |
|
|
|
|
| |
|
|
|
|
| ||||
3.Temperature | a. | Air sensor |
| a. When using an air sensor, the wine | ||||
fluctuating |
|
|
|
| bottle | temperature | is | mainly |
|
|
|
|
| controlled by the average air | |||
|
|
|
|
| temperature. If the | |||
|
|
|
|
| with the differential 4F, the cooling | |||
|
|
|
|
| unit turns on at 59°F of air | |||
|
|
|
|
| temperature and turns off at 55°F of | |||
|
|
|
|
| air temperature. The average air | |||
|
|
|
|
| temperature is 57°F, and then the | |||
|
|
|
|
| wine temperature is around 57+/- | |||
|
|
|
|
| 0.5°F. The air is light enough to | |||
|
|
|
|
| change so quickly that it maintains | |||
|
|
|
|
| relatively | constant | average | |
|
|
|
|
| temperature that would prevent wine | |||
|
|
|
|
| bottle temperature from varying. | |||
|
|
|
|
| ||||
4.Temperature | a. | Displaying 55°F, air sensor | a. | Move the air sensor away from the | ||||
high, unit |
| contacting the evaporator or in |
| evaporator and supply air |
| |||
stopping and |
| the supply air |
| b. | Lower setting |
|
| |
starting but | b. | Setting too high |
|
|
| |||
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| |
short |
|
|
|
|
|
|
|
|
running time |
|
|
|
|
|
|
|
|
5. Temperature | a. | Incorrect voltage |
| a. | Check for voltage |
|
| |
high, | b. | Failed thermistor |
| b. | Check thermistor by placing it in ice | |||
compressor |
|
|
|
| water and measuring resistance | |||
c. | Failed components |
| c. | Check compressor | windings, start | |||
stopping and |
| |||||||
|
|
|
| relay and overload protector. | ||||
starting but | d. | Improper condenser airflow | d. | Check for condenser fan |
| |||
short | e. | Dirty condenser |
| e. | Clean condenser |
|
| |
running time | f. | Overcharge of refrigerant | f. | Call service for removing refrigerant | ||||
| g. | Discharge or suction | pressure | g. | Call service for OEM information | |||
|
| too high |
|
|
|
|
|
|
- 12 -
