Vision Fitness T9800 Series manual E P 1 Orange BAG, E P 4 Motor Cover

A s s e m b l y			S T E P 3	PINK BAG
				• Insert the handlebar cover onto the
G u i d e				handlebar. Insert the right handlebar
				by holding the handlebar sideways
				toward the treadmill and inserting the
				top into the console. Rotate the
				handlebar into the bracket located on
				the console mast. Fasten with a bolt
	T9800 Series			(M5x12L), and a bolt (M6x15L socket
				head) & an arc washer (6.5x13x1T)
	TREADMILLS			into the two holes of the console plas-
				tic, and a bolt (M8x15L flat head) into
				the hole in the handlebar. Fasten a bolt
To avoid possible damage to this Platform Treadmill, please follow these assembly steps in the correct				(M6x15L socket head) and a flat washer
				(6.5x19x2T) into the hole in the handle-
order. Before proceeding though, find your new Platform Treadmill’s 2 serial numbers, located on the		S T E P 2		bar on the console mast. Do not fully
underside of the main frame, and on the bottom of the console, and enter here:				tighten the bolts.
				• Slide the handlebar cover over the
Frame Serial Number	Console Serial Number			bracket and secure with a bolt
Refer to these numbers when calling for service, and also enter these serial numbers on your Warranty				(M6x15L socket head) and a flat
				washer (6.5x19x2T). Do not fully
Card and in your own records. Be sure to read your Owner’s Guide before using your new Platform Treadmill.
			S T E P 3	tighten the bolt.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12				• Repeat on the left side.
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Platform				• Fully tighten the console and
Treadmill, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts				handlebar bolts.

are in place and partially threaded in before completely tightening any ONE bolt.

S T E P 1 ORANGE BAG

•Remove motor cover screws and take off the motor cover.

•Insert the right console mast to the right console mast bracket. First, fasten the inside of the console mast to the console mast bracket by securing four bolts (M8x15L socket head) and four washers (8.2x19x2T). Fully tighten the bolts. Second, fasten the two bolts (M10x20L button head) and two washers (10.2x19x2T) on the front of the console mast and fully tighten.

•Repeat on the left side

S T E P 2 BLUE BAG

•Tie the ribbon data cable, TV power cable, and coaxial cable to the cable wire tie on the top of the right console mast. Feed the cables down the console mast and through the hole at the lower part of the console mast. Remove protective plastic cover. Push any remaining cable into the console mast.

•Mount the console onto the left and right console masts using four bolts (M8x15L socket head) and four washers (8.2x19x2T). Do not fully tighten.

•Take the wire tie off the cables. Plug the large 20-pin ribbon connector into the 20-pin connector on the lower control board. Attach the two grounding wire connectors to the two grounding wires located in the motor pan near the front of the frame. Connect the TV power cable to the TV power connector and coaxial cable to the coaxial cable connector; both located on the inside of the motor compartment at the front of the treadmill.

TV Power Cable

Coaxial Cable

TV BRACKET WIRING

S T E P 1

S T E P 4 MOTOR COVER

• Place the motor cover back on the frame and fasten with 6 screws.

• Attach the power cord to the treadmill.

S T E P 4

• Plug the power cord into the power outlet.

S T E P 5	AUTO-CALIBRATION
	Please refer to back cover for this
	procedure, then return to Step 6.
S T E P 6	BELT TENSION
	• If the running belt slips when used,
	run the treadmill at 2.0 mph and use
	the supplied 8mm Allen wrench to turn
	the left and right tension bolts clockwise
	1/4-turn at a time until the belt no
	longer slips.
	• If the running belt is too far to the
	right side, run the treadmill at 2.0 mph
	and use the supplied 8mm Allen
	wrench to turn the right tension bolt
	clockwise 1/4-turn at a time until the
	belt remains centered during use.
S T E P 6	If the running belt is too far to the left
	side, run the treadmill at 2.0 mph and
	turn the left tension bolt clockwise
	1/4-turn at a time until the belt remains
	centered during use.