Vox VC-12 T

7

English

Rear Panel

1 2

1. VOX BUS MAIN connector

This connector is used to connect the VC-12

to a Valvetronix amp or VOX BUS-compatible

device. Use the included 10Base-T “straight”

cable for this.

2. VOX BUS SUB connector

This connector allows you to connect a

second Valvetronix amp or VOX BUS-compat-

ible device to the VC-12 for simultaneous

control of two devices.

Note: Since the second device cannot

transmit control signals to the VC-12, you

must use the VC-12 in order to control both

devices simultaneously.

To ampTo amp

Control

Control

Power

Power

MAIN SUB

Using Your VC-12

This section explains how to select

programs, control effects, use the built-

in tuner, use Manual mode, and store

Valvetronix Amp program data in the VC-12.

Channel Select Mode

Channel Select Mode is used to select

programs.

Selecting Channel Select Mode

In Channel Select Mode, the BANK display

shows the number of the current bank. If a

bank number is not displayed, you can select

Channel Select Mode using the following

methods:

•If the BANK display shows , Effect On/

Off mode is selected and you need to

press the CHANNEL–FX ON/OFF switch

to select Channel Select Mode.

•If the BANK display shows , , or a

note name, the Tuner is on. Press the

TUNER switch to turn off the tuner and

return to the previous mode. If the BANK

display shows a bank number, you are

already in Channel Select Mode. If it

shows , you are in Effect On/Off mode

and need to press the CHANNEL–FX ON/

OFF switch to select Channel Select

Mode.

•If the BANK display is flashing, you must

have selected another bank but not yet

selected another program. Press the

CHANNEL–FX ON/OFF switch to return to

the previous mode.

•If the BANK display shows , your

Valvetronix amp is in Manual mode, in

which case you’ll need to cancel Manual

mode on your amp before proceeding.

Contents

Main Page Precautions Location Interference with other electrical devices Handling Care C Features Care Hooking Up the VC-12 T Features of the VC-12 Top Panel 5. RECALL switch 6. Effects section switches 14 & LEDs 7. CHANNELFX ON/OFF switch & LED 8. Expression pedal, Pedal switch Expression pedal T 1 2 1. VOX BUS MAIN connector 2. VOX BUS SUB connector Using Your VC-12 Effect On/Off Mode Selecting Effect On/Off Mode Switching Effects On & Off Selecting Programs in Effect On/Off Mode Using the Tuner About Manual Mode Storing Amp Program Data in the VC-12 Storing Program Data Loading Program Data Loading Program Data into Two Amps Deleting VC-12 Program Data Expression & Volume Pedal T Calibrating the Pedals Calibrating the Expression Pedal Calibrating the Volume Pedal Selecting a Volume Pedal Curve Re-selecting the default curve User Hint Troubleshooting The VC-12 doesnt turn on when I turn on the connected device? My amp produces no sound? Cant turn effects on or off from the VC-12? The Expression pedal doesnt work? Prcautions Emplacement Interfrences avec dautres appareils lectriques Maniement Entretien T Fonctions Entretien Brancher le VC-12 T A propos du cble fourni Fonctions du VC-12 3. Commutateur et diode TAP 1. Commutateurs BANK UP/DOWN 2. Affichage BANK Face avant 4. Commutateur et diodes TUNER 7. 5. Commutateur RECALL 6. Commutateurs 14 et diodes deffets Commutateur et diode CHANNELFX ON/OFF C Face arrire 1 2 1. Prise VOX BUS MAIN 2. Prise VOX BUS SUB Mode dactivation/de coupure deffet Slectionner le mode dactivation/de coupure deffet Activer/couper les effets Choisir des mmoires en mode dactivation/de coupure deffet Utiliser la fonction daccordeur A propos du mode manuel Sauvegarder les rglages de lampli dans le VC-12 Transfert des mmoires de lampli Transmettre des rglages Transmettre les rglages deux amplis Effacer des mmoires Pdale dexpression et pdale de volume D Calibrer les pdales Calibrer la pdale dexpression Calibrer la pdale de volume Choisir la courbe de la pdale de volume Slectionner la courbe Tuyau En cas de problme Le VC-12 ne sallume pas quand je mets lappareil connect sous tension. Mon ampli ne produit aucun son. Impossible dactiver/de couper les effets avec le VC-12. La pdale dexpression ne fonctionne pas. Vorsichtsmanahmen Aufstellungsort Streinflsse auf andere Elektrogerte Bedienung Reinigung G Features Pflege Anschlieen des VC-12 D Funktionen des VC-12 3. TAP-Futaster und -Diode 4. TUNER-Futaster und -Dioden 1. BANK UP/DOWN-Futaster 2. BANK-Display 5. RECALL-Futaster 6. Futaster und Dioden 14 fr die Effekte 7. CHANNELFX ON/OFF-Futaster und -Diode 8. Schwellpedal, Futaster Schwellpedal H 1 2 1. VOX BUS MAIN-Anschluss 2. VOX BUS SUB-Anschluss Arbeiten mit dem VC-12 Effektpedalmodus Anwahl des Effektpedalmodus Ein- und Ausschalten der Effekte Speicheranwahl im Effektpedalmodus Verwendung der Stimmfunktion (Tuner) ber den Manual-Modus Speichern der Verstrkereinstellungen im VC-12 Speichern der Einstellungen bertragen der Einstellungsdaten bertragen der Einstellungsdaten zu zwei Verstrkern Lschen eines Speicherbereichs Schwell- und Volumenpedal H Kalibrieren der Pedale Kalibrieren des Schwellpedals Kalibrieren des Volumenpedals Anwahl der Pegelkurve fr das Volumenpedal Anwahl einer Kurve Tipp Fehlersuche Warum tut der VC-12 beim Einschalten des angeschlossenen Gertes nichts? Warum gibt mein Verstrker keinen Mucks von sich? Warum kann ich die Effekte nicht vom VC-12 aus ein-/ausschalten? Warum funktioniert das Schwellpedal nicht?