Vox VC-12 Selecting a Volume Pedal Curve

13

English

4. Press the TAP switch to enter the mini-

mum position.

The BANK display shows .

5. To set the maximum position, slowly

press the Volume pedal down. When it’s

down as far as it’ll go, take your hand

off.

If you want to cancel the procedure at this

point, press the RECALL switch.

6. Press the TAP switch to enter the maxi-

mum position.

The BANK display shows for one

second, after which the VC-12 is ready for

use.

If for some reason the calibration process

didn’t work, and will appear alter-

nately on the BANK display and you

should repeat the procedure starting at

step #3.

Note: If the calibration process fails repeat-

edly, the VC-12 may be in need of repair and

you should contact your VOX dealer.

Selecting a Volume Pedal Curve

There are three Volume pedal response

curves for you to choose from. These deter-

mine the speed at which the volume changes

as the Volume pedal is operated, as shown

below.

Pedal position

Volume

Up

Quiet

Down

Loud

1

2

3

Curve #1: The volume changes slowly in the

upper range of the pedal’s travel; quickly in

the lower range.

Curve #2: With this standard curve, the

volume changes throughout the pedal’s

travel. This is the initial setting.

Curve #3: The volume changes quickly in the

upper range of the pedal’s travel; slowly in the

lower range.

Re-selecting the default curve

1. Turn off the connected device.

2. While holding down the VC-12’s BANK

UP switch and switch #1, #2, or #3, turn

on the connected device.

The number of the selected curve (C1, C2,

or C3) appears on the BANK display for

one second. Since the VC-12 remembers

which volume curve you select, there’s no

need to select it again the next time you

use your VC-12.

User Hint

The default curve (No. 2) is the standard

Audio Taper pot curve, as used in most

commercial volume pedals, and as such is

extremely useful for most purposes. By

selecting either of the other two curves you

can fine-tune the operation of the pedal to

what feels most comfortable to yourself. As

with most things in life, please feel free to

experiment, as only you know what suits

you best.

Contents

Main Page Precautions Location Interference with other electrical devices Handling Care C Features Care Hooking Up the VC-12 T Features of the VC-12 Top Panel 5. RECALL switch 6. Effects section switches 14 & LEDs 7. CHANNELFX ON/OFF switch & LED 8. Expression pedal, Pedal switch Expression pedal T 1 2 1. VOX BUS MAIN connector 2. VOX BUS SUB connector Using Your VC-12 Effect On/Off Mode Selecting Effect On/Off Mode Switching Effects On & Off Selecting Programs in Effect On/Off Mode Using the Tuner About Manual Mode Storing Amp Program Data in the VC-12 Storing Program Data Loading Program Data Loading Program Data into Two Amps Deleting VC-12 Program Data Expression & Volume Pedal T Calibrating the Pedals Calibrating the Expression Pedal Calibrating the Volume Pedal Selecting a Volume Pedal Curve Re-selecting the default curve User Hint Troubleshooting The VC-12 doesnt turn on when I turn on the connected device? My amp produces no sound? Cant turn effects on or off from the VC-12? The Expression pedal doesnt work? Prcautions Emplacement Interfrences avec dautres appareils lectriques Maniement Entretien T Fonctions Entretien Brancher le VC-12 T A propos du cble fourni Fonctions du VC-12 3. Commutateur et diode TAP 1. Commutateurs BANK UP/DOWN 2. Affichage BANK Face avant 4. Commutateur et diodes TUNER 7. 5. Commutateur RECALL 6. Commutateurs 14 et diodes deffets Commutateur et diode CHANNELFX ON/OFF C Face arrire 1 2 1. Prise VOX BUS MAIN 2. Prise VOX BUS SUB Mode dactivation/de coupure deffet Slectionner le mode dactivation/de coupure deffet Activer/couper les effets Choisir des mmoires en mode dactivation/de coupure deffet Utiliser la fonction daccordeur A propos du mode manuel Sauvegarder les rglages de lampli dans le VC-12 Transfert des mmoires de lampli Transmettre des rglages Transmettre les rglages deux amplis Effacer des mmoires Pdale dexpression et pdale de volume D Calibrer les pdales Calibrer la pdale dexpression Calibrer la pdale de volume Choisir la courbe de la pdale de volume Slectionner la courbe Tuyau En cas de problme Le VC-12 ne sallume pas quand je mets lappareil connect sous tension. Mon ampli ne produit aucun son. Impossible dactiver/de couper les effets avec le VC-12. La pdale dexpression ne fonctionne pas. Vorsichtsmanahmen Aufstellungsort Streinflsse auf andere Elektrogerte Bedienung Reinigung G Features Pflege Anschlieen des VC-12 D Funktionen des VC-12 3. TAP-Futaster und -Diode 4. TUNER-Futaster und -Dioden 1. BANK UP/DOWN-Futaster 2. BANK-Display 5. RECALL-Futaster 6. Futaster und Dioden 14 fr die Effekte 7. CHANNELFX ON/OFF-Futaster und -Diode 8. Schwellpedal, Futaster Schwellpedal H 1 2 1. VOX BUS MAIN-Anschluss 2. VOX BUS SUB-Anschluss Arbeiten mit dem VC-12 Effektpedalmodus Anwahl des Effektpedalmodus Ein- und Ausschalten der Effekte Speicheranwahl im Effektpedalmodus Verwendung der Stimmfunktion (Tuner) ber den Manual-Modus Speichern der Verstrkereinstellungen im VC-12 Speichern der Einstellungen bertragen der Einstellungsdaten bertragen der Einstellungsdaten zu zwei Verstrkern Lschen eines Speicherbereichs Schwell- und Volumenpedal H Kalibrieren der Pedale Kalibrieren des Schwellpedals Kalibrieren des Volumenpedals Anwahl der Pegelkurve fr das Volumenpedal Anwahl einer Kurve Tipp Fehlersuche Warum tut der VC-12 beim Einschalten des angeschlossenen Gertes nichts? Warum gibt mein Verstrker keinen Mucks von sich? Warum kann ich die Effekte nicht vom VC-12 aus ein-/ausschalten? Warum funktioniert das Schwellpedal nicht?