Manuals / VTech / Communications / Cordless Telephone

VTech VT 1930c Changing Stored Numbers, Deleting Stored Numbers, Deleted, Storing Special Codes

Models: VT 1930c

1 43

Download 43 pages 44.29 Kb

Page 31

MEMORY DIALING

¥Press MEM/PGM again to exit memory dial mode and leave the number on the display.

¥Press PHONE . The number on the display will be dialed after a 2 second pause.

¥Note that if digits were on the display prior to entering memory dial mode, the contents of the speed dial memory will be appended to those digits. For example, if 1503 was on the display and the contents of the memory location is 6438981, then the display would show the following upon exiting memory dial mode:

Changing Stored Numbers

To change or replace a stored number simply enter the new number on the display and store it in the memory location you wish to change.

Deleting Stored Numbers

¥Press MEM/PGM . The display will change to "SPEED DIAL LOCATION_ _".

¥Enter memory location number (00..20).

¥Press CLR/DEL key. The display will change to "LOCATION XX

DELETED".

¥ Press OFF to exit.

NOTE:

Stored numbers are retained in memory even if the base loses its power or the handset battery is removed.

Storing Special Codes

To insert a pause in a phone number, press HOLD at the appropriate point when entering the number . This inserts a 2 second pause. A " P " appears in the display to show the pause. For longer pauses, press HOLD two or more times. Each press makes the pause 2 seconds longer and is treated as a stored digit.

If your phone is connected to a PBX, you can store the PBX access number and a pause before the phone number. For example, to store 9- PAUSE-555-1234 in memory location 08, do the following:

1. Press

9

2.Press HOLD

3.Dial 5551234

4.Press and hold MEM/PGM

5.Enter 08

31

Image 31

VTech VT 1930c manual Changing Stored Numbers, Deleting Stored Numbers, Deleted, Storing Special Codes

Contents

Introduction Special Features Wall Mounting Parts Check ListFCC Part FCC and IC RegulationsFCC and IC Regulations FCC and IC Regulations Read and understand all instructions Important Safety InstructionsImportant Safety Instructions Word About Rechargeable Batter- ies Replacing the Battery PackTo Charge The Battery Pack Its Impossible To Overcharge The Battery PackDownward To Replace The Handset Battery Pack Follow The Steps BelowReplacing a Drained Handset battery Spare Battery ChargerInstallation Power BackupHandset Ringer Getting StartedFill in the telephone number card on the base unit Wall Mounting Handset Display Messages Examples of the Handset DisplayLCD DISPLAY-EXAMPLES Base Unit Function Keys Handset Layout Base Unit Layout Base Unit Features INT.CO Quick Reference GuideStoring Memory Speed Dial Numbers From the Base Unit Press the Speaker Phone key Memory Dialing speed DialingFrom the Handset ¥ Press MEM/PROGFrom the Base Unit Using Redial From the HandsetRedial Hold Mute Basic OperationFlash RedialBasic Operation Message Waiting Switching calls using FlashAdvanced Functions Call WaitingProgramming The Ringer Temporary ToneChanging Ringer Types Advanced Functions Advanced Dialing Clear/Delete CLR/DEL KeyMulti Level Redial Storing Memory Speed Dial numbers Memory DialingDialing From Memory From the Handset Storing Special Codes Changing Stored NumbersDeleting Stored Numbers DeletedReceiving and Storing Calls Caller ID CIDDialing From Caller ID CID Memory Private Special Message Indicators Out of Area CallsTransmission Error ÒPrivateÓ CallsReviewing Number Reviewing NumbersDeleting Numbers Out Of Range indication Additional Operating TipsNoise Or Interference Automatic Security CodingElectrical storms MaintenanceCleaning your telephone Avoid waterPhone Doesnõt Work AT ALL Handset does not Ring When YOU Receive a CallYOU Hear Other Calls While Using Your Phone Case of DifficultyCommon Cure for Electronic Equipment Warranty Statement Technical Specifications Table of Contents Issue