WCP85

Installation

(Continued)

furnace drain (if applicable), to the inlet holes on the pump. Refer to Figure 5.

STEP 4: INSTALLATION OF DISCHARGE LINE

NOTE: Use 3/8” I.D. (max.) flexible tubing.. A hose clamp is recommended (not provided).

A.Extend discharge pipe from barbed check valve to the highest point possible. Refer to Figure 6.

B.From this point, direct the discharge line to the location of the drainage source. Maintain a continuous downward slope.

NOTE: Construct an inverted “U” (see Figure 6) at the highest point of discharge line if a continuous downward slope is not possible. Exercise care not to kink or “pinch off” the flow of condensate liquid.

STEP 5: INSTALLATION OF SAFETY SWITCH (IF APPLICABLE)

Connect power cord to a constant

voltage source. Do not connect to a fan or other device that may run intermittently.

A.The pump can be wired directly to the appliance thermostat to shut the pump and appliance down in the event of pump failure. Refer to Figure 7 for typical wiring diagram.

NOTE: The alarm can be wired in the safety switch at the normally open (“NO”) contact.

TIPS FOR EASY INSTALLATION

1.After reading instructions, check to make sure installation does not exceed a maximum of 15 feet of vertical lift.

2.Make sure pump is level. No part of the pump base should be more than 1/8” off of level plane.

3.Use soapy water on unit when performing cleaning maintenance. (Refer to Maintenance guidelines.)

4.For optimum performance, drain and discharge lines should have a continuous downward slope. Test operation of pump to make sure lines have enough downward slope

Figure 4 - Modification of pipe end to prevent blockage

Main Drain from Coil

High efficiency

gas furnaceOverflow Drain from Coil When Required

GFCI

Outlet

Condensate Neutralizer

Main Drain

Overflow Drain

Cartridge (If Required)

from Furnace

from Furnace

Figure 5 - Plumbing pipe from drain to inlet holes on pump

Do not kink or pinch

To Main Drain

3/8” ID Tubing

Inverted “U”

15 Ft.

Max

GFCI

Outlet

Hose clamp

(recommended, not included)

Figure 6 - Installation of discharge line

3

Page 2 Page 4
Page 3
Image 3
Wayne 370100-001 Installation of Discharge Line, Installation of Safety Switch if Applicable, Tips for Easy Installation
Page 2 Page 4

370100-001, WCP85 specifications

The Wayne 370100-001, also known as the WCP85, is a versatile and highly efficient fuel dispenser that epitomizes innovation and reliability in the fuel retail industry. It is designed to meet the demands of various fueling environments while providing an unparalleled user experience. The WCP85 series stands out for its robust construction and advanced technological features that ensure optimal performance.

One of the primary characteristics of the Wayne WCP85 is its modular design, which allows for easy customization according to the specific needs of fuel retailers. This adaptability enables operators to configure the dispenser for multiple fuel types, including gasoline, diesel, and alternative fuels, thereby catering to a wide range of customer preferences. Additionally, its ability to support different payment systems makes it compatible with various payment methods, enhancing the customer experience at the pump.

The WCP85 incorporates advanced measurement technology that ensures accurate fuel dispensing. Its state-of-the-art flow meters are designed to meet or exceed industry standards, reducing the risk of inaccuracies and boosting customer trust. Furthermore, the dispenser is equipped with high-speed pumping capabilities, allowing for faster transactions and reduced wait times for customers.

In terms of safety and compliance, the Wayne WCP85 is designed with robust leak detection and monitoring systems. These features not only adhere to regulatory requirements but also enhance the overall safety of fuel dispensing operations. The dispenser also includes features such as emergency shut-off systems and anti-tampering mechanisms to further ensure safety in potentially hazardous environments.

An important feature of the WCP85 is its user-friendly interface, which includes a high-resolution display and intuitive navigation. This makes it easy for customers to select fuel types, enter payment information, and access promotional content. Additionally, the dispenser's design incorporates ergonomic elements, ensuring that it meets the needs of all users.

Moreover, the WCP85 supports connectivity options, allowing for seamless integration with backend systems, payment processors, and loyalty programs. This connectivity enhances operational efficiency and can help fuel retailers gather valuable data for optimizing their operations.

In summary, the Wayne 370100-001 WCP85 is a cutting-edge fuel dispenser that combines flexibility, safety, and advanced technology, making it an ideal choice for fueling stations looking to enhance their service quality and operational efficiency. With its robust construction, user-friendly features, and reliable performance, the WCP85 is poised to meet the evolving demands of the fuel retail landscape.
Top Page Image Contents