OPERATION

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 17/32 washer, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

GAUGE WHEEL

MOUNTING

BRACKET

3/8-16

LOCKNUT

3/8 WASHER

SHOULDER

GAUGE WHEEL

BOLT

17/32 WASHER

 

FIG. 6

TO OPERATE MOWER (See Fig. 7)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT LIFT

LEVER HIGH POSITION

ATTACHMENT CLUTCH LEVER

"DISENGAGED"

POSITION

LOW POSITION

DEFLECTOR

SHIELD

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

•The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Customer Responsibilities section of this manual).

•To change engine oil, see the Customer Responsibilities section in this manual.

FIG. 7

12

Page 11 Page 13
Page 12
Image 12
Weed Eater 180530 Before Starting the Engine, To Operate on Hills, To Transport, Towing Carts and Other ATTACH- Ments
Page 11 Page 13

180530 specifications

The Weed Eater 180530 is a powerful and efficient string trimmer designed to make yard maintenance easier and more effective. With its robust features and modern technology, this tool stands out as a reliable choice for both amateur gardeners and professional landscapers.

One of the main features of the 180530 is its lightweight design, allowing for easy maneuverability and reduced user fatigue during extended use. Weighing in at just around 8 pounds, it is easy to handle, making it suitable for users of all experience levels.

Powering the Weed Eater 180530 is a 25cc 2-cycle engine, which delivers impressive performance and efficiency. This engine provides rapid acceleration and effective cutting capabilities, allowing users to tackle tough weeds and thick grass with ease. The 2-cycle engine design is known for its simplicity and ease of maintenance, ensuring that users can quickly get back to work.

The 180530 features an automatic dual line feed system, which ensures that the cutting line is always at the optimal length during operation. This reduces downtime associated with manual line adjustments, thereby enhancing productivity. The trimmer is equipped with a straight shaft, which extends reach and makes it easier to access difficult areas.

Another standout characteristic of the Weed Eater 180530 is its versatility. This trimmer is designed to accept a variety of attachments, allowing users to switch between functions such as edging, blowing, and cultivating with ease. This adaptability provides excellent value for users who want a multi-functional landscape tool.

Safety is also prioritized in the design of the 180530. It comes with an easy-to-operate throttle control that allows users to manage the power output effectively. Additionally, the protective guard helps to shield the user from debris while operating, enhancing overall safety during use.

In conclusion, the Weed Eater 180530 combines powerful performance with a lightweight and user-friendly design. Its versatile capabilities, efficient engine technology, and safety features make it a valuable addition to any yard care toolkit. Whether tackling a small garden or maintaining larger landscapes, the 180530 is well-equipped to handle a variety of trimming tasks, ensuring beautifully maintained outdoor spaces.
Top Page Image Contents