Engine, Battery, Belts, Transaxle Cooling

CUSTOMER RESPONSIBILITIES

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Open battery box door.

•Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY” in the Service and Adjustments section of this manual).

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt and chaff which can restrict cooling.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SF-SJ. Select the oil’s SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

							SAE 30
			5W-30

F	-20	0			30 32 40		60	80	100
C	-30	-20		-10	0	10	20	30	40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the tractor is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/ dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Fig. 11)

Determine temperature range expected before oil change. All oil must meet API service classification SF-SJ.

•Be sure tractor is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

•Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil.

•Remove yellow cap from bottom fitting of drain valve and install the drain tube onto the fitting.

		OIL DRAIN VALVE
	CLOSED AND
	LOCKED
	POSITION
	YELLOW	DRAIN
	CAP	DRAIN
	CAP	TUBE
		TUBE

FIG. 11

•Unlock drain valve by pushing inward and turning coun- terclockwise.

•To open, pull out on the drain valve.

•After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

•Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve.

•Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

•Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

180530 specifications

The Weed Eater 180530 is a powerful and efficient string trimmer designed to make yard maintenance easier and more effective. With its robust features and modern technology, this tool stands out as a reliable choice for both amateur gardeners and professional landscapers.

One of the main features of the 180530 is its lightweight design, allowing for easy maneuverability and reduced user fatigue during extended use. Weighing in at just around 8 pounds, it is easy to handle, making it suitable for users of all experience levels.

Powering the Weed Eater 180530 is a 25cc 2-cycle engine, which delivers impressive performance and efficiency. This engine provides rapid acceleration and effective cutting capabilities, allowing users to tackle tough weeds and thick grass with ease. The 2-cycle engine design is known for its simplicity and ease of maintenance, ensuring that users can quickly get back to work.

The 180530 features an automatic dual line feed system, which ensures that the cutting line is always at the optimal length during operation. This reduces downtime associated with manual line adjustments, thereby enhancing productivity. The trimmer is equipped with a straight shaft, which extends reach and makes it easier to access difficult areas.

Another standout characteristic of the Weed Eater 180530 is its versatility. This trimmer is designed to accept a variety of attachments, allowing users to switch between functions such as edging, blowing, and cultivating with ease. This adaptability provides excellent value for users who want a multi-functional landscape tool.

Safety is also prioritized in the design of the 180530. It comes with an easy-to-operate throttle control that allows users to manage the power output effectively. Additionally, the protective guard helps to shield the user from debris while operating, enhancing overall safety during use.

In conclusion, the Weed Eater 180530 combines powerful performance with a lightweight and user-friendly design. Its versatile capabilities, efficient engine technology, and safety features make it a valuable addition to any yard care toolkit. Whether tackling a small garden or maintaining larger landscapes, the 180530 is well-equipped to handle a variety of trimming tasks, ensuring beautifully maintained outdoor spaces.

Weed Eater 180530 manual Engine, Battery, Belts, Transaxle Cooling, Lubrication

Models: 180530