SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 16 and 17)

Raise mower to its highest position.

At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

If adjustment is necessary, make adjustment on one side of mower only.

To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

Recheck measurements after adjusting.

BOTTOM EDGE

BOTTOM EDGE

OF MOWER

OF MOWER

TO GROUND

TO GROUND

“A”

“A”

 

GROUND LINE

FIG. 16

SUSPENSION ARM

LIFT LINK

ADJUSTMENT

NUT

FIG. 17

FRONT-TO-BACK ADJUSTMENT (See Figs. 18 and 19)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

Before making any necessary adjustments, check that both front links are equal in length.

If links are not equal in length, adjust one link to same length as other link.

To lower front of mower loosen nut “E” on both front links an equal number of turns.

20

When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.

When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 18

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 19

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 20)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

Work belt off both mandrel pulleys and idler pulleys.

Pull belt away from mower.

BELT INSTALLATION -

Install new belt in reverse order of removal.

Make sure belt is in all pulley grooves and inside all belt guides.

Install mower in reverse order of removal instructions.

MANDREL

IDLER PULLEYS

PULLEY

 

MANDREL

PULLEY

FIG. 20

Page 20
Image 20
Weed Eater 180530 manual To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal, Belt Installation

180530 specifications

The Weed Eater 180530 is a powerful and efficient string trimmer designed to make yard maintenance easier and more effective. With its robust features and modern technology, this tool stands out as a reliable choice for both amateur gardeners and professional landscapers.

One of the main features of the 180530 is its lightweight design, allowing for easy maneuverability and reduced user fatigue during extended use. Weighing in at just around 8 pounds, it is easy to handle, making it suitable for users of all experience levels.

Powering the Weed Eater 180530 is a 25cc 2-cycle engine, which delivers impressive performance and efficiency. This engine provides rapid acceleration and effective cutting capabilities, allowing users to tackle tough weeds and thick grass with ease. The 2-cycle engine design is known for its simplicity and ease of maintenance, ensuring that users can quickly get back to work.

The 180530 features an automatic dual line feed system, which ensures that the cutting line is always at the optimal length during operation. This reduces downtime associated with manual line adjustments, thereby enhancing productivity. The trimmer is equipped with a straight shaft, which extends reach and makes it easier to access difficult areas.

Another standout characteristic of the Weed Eater 180530 is its versatility. This trimmer is designed to accept a variety of attachments, allowing users to switch between functions such as edging, blowing, and cultivating with ease. This adaptability provides excellent value for users who want a multi-functional landscape tool.

Safety is also prioritized in the design of the 180530. It comes with an easy-to-operate throttle control that allows users to manage the power output effectively. Additionally, the protective guard helps to shield the user from debris while operating, enhancing overall safety during use.

In conclusion, the Weed Eater 180530 combines powerful performance with a lightweight and user-friendly design. Its versatile capabilities, efficient engine technology, and safety features make it a valuable addition to any yard care toolkit. Whether tackling a small garden or maintaining larger landscapes, the 180530 is well-equipped to handle a variety of trimming tasks, ensuring beautifully maintained outdoor spaces.