LINE REPLACEMENT

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut a length of 20 feet of 0.080! (2 mm) diameter Weed Eaterr brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert one end of the line about 1/2 inch (1 cm) into the small hole on the inside of spool.

Small

 

 

 

 

 

Hole

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Spool

 

Line in Notch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10.Pull the line extending outside of the hub to release the line from the notch.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head will be spinning during this procedure. Wear your protective equipment and observe all safety precautions.

The carburetor has been carefully set at the fac- tory. Adjustments may be necessary if you no- tice any of the following conditions:

SEngine will not idle when the throttle is re- leased.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making adjustments. Keep all parts of your body away from the cut- ting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow).

S Turn idle speed screw clockwise to in- crease engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed.

Hub

Line exit hole

 

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrow found on the spool.

6.Push the line into the notch, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the line into the exit hole in the hub as shown in the illustration.

8.Align the notch with the line exit hole.

9.Push spool into hub until it snaps into place.

Idle Speed

Screw

Air Filter

Cover

If you require further assistance or are unsure about performing this procedure, contact an au- thorized service dealer or call 1--800--554--6723.

WARNING: Perform the following steps after each use:

S Allow engine to cool, and secure the unit before storing or transporting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric

motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci- dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

SClean the entire unit before lengthy storage. S Store in a clean dry area.

SLightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom- mended type and heat range.

8

Page 7 Page 9
Page 8
Image 8
Weed Eater 530163438 instruction manual Line Replacement, Carburetor Adjustment, Seasonal Storage, Fuel System, Engine
Page 7 Page 9

530163438 specifications

The Weed Eater 530163438 is a powerful and versatile lawn care tool that has gained popularity among homeowners and professional landscapers alike. This efficient string trimmer is designed to deliver high-performance cutting capability while prioritizing ease of use and reliability.

One of the standout features of the Weed Eater 530163438 is its lightweight design, which enables users to maneuver the trimmer effortlessly. Weighing in at just over 10 pounds, it reduces fatigue during extended use, making it an ideal choice for tackling large yards or detailed landscaping projects. The trimmer’s balance and ergonomic handle allow for comfortable operation, ensuring that users can maintain control while trimming around flower beds, walkways, and fences.

Equipped with a robust two-stroke engine, the Weed Eater 530163438 provides sufficient power to handle tough grasses and weeds. The engine is designed for efficient fuel consumption, allowing longer run times without frequent refueling. This feature is particularly beneficial for professional landscapers who require reliable performance throughout their workday.

The dual-line cutting system of the Weed Eater 530163438 ensures a clean and precise cut every time. It utilizes a bump feed mechanism, which allows users to easily advance the line by tapping the head on the ground. This feature minimizes interruptions and enhances productivity, making it easier to manage various landscaping tasks efficiently.

Another noteworthy characteristic of the Weed Eater 530163438 is its versatility. The trimmer comes with different attachments, allowing users to convert it into various tools, such as a blower or edger. This adaptability makes it a valuable addition to any outdoor toolkit, capable of handling an array of tasks beyond just trimming.

Durability is also built into the design of the Weed Eater 530163438. Constructed with high-quality materials, it withstands the rigors of outdoor use while maintaining its performance over time. Furthermore, the ease of maintenance, including accessible air filters and spark plugs, ensures that users can keep the trimmer in peak condition with minimal effort.

In conclusion, the Weed Eater 530163438 is a feature-rich string trimmer that combines ease of use, power, and versatility. Its lightweight build, efficient engine, dual-line cutting system, and adaptability make it an excellent choice for both amateur gardeners and landscaping professionals seeking a reliable tool to maintain their outdoor spaces.
Top Page Image Contents