Manuals / Weed Eater / Lawn and Garden / Lawn Mower

Weed Eater HD12538G TO ADJUST THROTTLE CONTROL CABLE See Fig, Service And Adjustments, Engine

Models: 165412 HD12538G

1 52

Download 52 pages 38.49 Kb

Page 24

TO ADJUST THROTTLE CONTROL CABLE

SERVICE AND ADJUSTMENTS

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

(See Fig. 27)

The throttle control has been preset at the factory and ad- justment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

aWith engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

aCheck that holes "A" in ?overnor control lever and hole in governor plate line-up. I holes "Anare not aliBned, loosen clamp screw and move throttle cable unti holes are aligned. Tighten clamp screw securely.

TO ADJUST CARBURETOR The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, alti- tude or load. If the carburetor does need adjustment, see engine manual.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVER- NOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FAC- TORY HlGH SPEED SETTING CAN B E DANGEROUS. IF YOU THINKTHE ENGINE-GOVERNEDHlGH SPEED NEEDS ADJUSTING. CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTERIDEPARTMENT, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECES- SARY ADJUSTMENTS.

GOVERNOR

CONTROL PLATE

FIG. 27

Image 24

Weed Eater HD12538G TO ADJUST THROTTLE CONTROL CABLE See Fig, Service And Adjustments, Engine, Governor Control Plate

Contents

Assembly Operation 9Customer Responsibilities 9Service and Adjustments @Storage TroubleshootingRepair Parts 165412 04.24.98 RDSAFETY RULES IV. SERVICESafe Operation Practices for Ride-OnMowers a I.GENERAL OPERATIONCUSTOMER RESPONSIBILlflES PRODUCT SPEClFlCMlONSDATE OF PLIRCHASE TABLE OF CONTENTS LIMITED WARRANTYSAFETY RULES MAINTENANCE SCHEDULECONTENTS OF HARDWARE PACK 1Large Flat Washer 1Lockwasher 1Locknut 5112Hex Nuts 1/4-20 ASSEMBLY TOOLS REQUIRED FOR ASSEMBLYTO REMOVE TRACTOR FROM CARTON BEFORE ROLLING TRACTQR OFF SKlDWOW TO SET UP YOUR TRACTOR CONNECT BATTERY See Figs. 2 andINSTALL SEAT See Fig FIG.J CHECKLIST CHECK TIRE PRESSURECHECK DECK LEVELNESS CHECK FOR PROPER POSITION OF ALL BELTSPage OPERATION KNOW YOUR TRACTORFIG. THROTTLWCHOKE CONTROL: Used for starting andHOW TO USE YOUR TRACTOR TO ADJUST MOWER CUTTING HEIGHT See Fig.TO SET PARKING BRAKE See Fig. TO USE THROTLE CONTROL See Fig.BEFORE STARTING THE ENGINE TO OPERATE MOWER See Fig.TO TRANSPORT CHECK ENGINE OIL LEVEL See Fig.MOWING TIPS TO START ENGINE See Fig.OPERATION FIG.LUBRICKTION CHART CUSTOMER RESPONSIBILGENERAL RECOMMENDATIONS I I I I 1 I I I ICUSTOMER RESPONS TRACTORBRAKE OPERATION TIRESCUSTOMER RESPONSIBILITIES ENGINEBArrERY V-BELTSCLEAN AIR SCREEN See Fig. CUSTOMER RESPONSIBAIR FILTER See Fig ENGINE COOLING FINS See Fig.CLEANING MUFFLERSPARK PLUGS IN-LINEFUEL FILTER See Fig.TO INSTALL MOWER See Fig. TO REMOVE MOWER See Fig.SERVICE AND ADJUSTMENTS SERVICE AND ADJUSTMENTS TO- - LEVEL MOWER HOUSINGFIG. FIG.TO ADJUST BRAKE See Fig. TO REPLACE MOWER BLADE DRIVE BELT See Fig.TO REPLACE MOTION DRIVE BELT See Fig. SERVICE AND ADJUSTMENTSSERVICE AND ADJUSTMENTS TO ADJUST SFEERINGWHEEL ALIGNMENTFRONT WHEEL TOE-INICAMBER TO REMOVE WHEEL FOR REPAIRS See Fig.TO REMOVE HOOD AND GRILL ASSEMBLY See Fig. T0,START ENGINE WITH A WEAK BAlTERY See Fig.TO REPLACE HEADLIGHT BULB INTERLOCKS AND RELAYSTO ADJUST THROTTLE CONTROL CABLE See Fig. SERVICE AND ADJUSTMENTSENGINE GOVERNOR CONTROL PLATEBATTERY STORAGETRACTOR OTHERTROUBLESHOOT NG POINTS CORRECTIONLoss of power startTROUBLESHOOTING POINTS PROBLEMrotate SERVICE NOTES SCHEMATIC TRACTOR - - MODEL NUMBER HD12538GAREPAIR PARTS TRACTOR - - MODEL NUMBER HD125386ELECTRICAL REPAIR PARTS f RACTOR - - MODEL NUMBER HD12538CKEY PART NO. NO. DESCRIPTION ELECTRICALREPAIR PAWS CHASSIS AND ENCLOSURESTRACTOR - - MODEL NUMBER HD125386 TRACWOR - - MODEL NUMBER HDl2538G KEY PART NO. NO. DESCRIPTIONREPAIR PARTS CHASSIS AND ENCLOSURESTRACTOR- - MODEL NUMBER HD125386 DRIVEREPAIR PARTS KEY PART NO. NO. DESCRIPTIONREPAIR PARTS TRACTOR - - MODEL NUMBER HD12538GSTEERING ASSEMBLY TRAGTOR - - MOD- NLIMBER HB12538GREPAIR PARTS TRACTOR - - MODEL NUMBER HD125386 Screw lT #lo-325 318 FlangeREPAIR PARTS STEERING ASSEMBLYSEAT ASSEMBLY TRACTOR - - MODEL NUMBER HD12538CREPAIR PARTS KEY PART NO. NO. DESCRIPTIONDECALS WHEELS & TIRESPART DESCRIPTIONTRACTOR - - MODEL NLIMBER HD125386 ENGINEREPAIR PARTS REPAIR PARTS TRACTOR - - MODEL NUMBER HD12538GENGINE KEY PARTLlFT REPAIR PARTSTRACTOR - - MODEL NUMBER HD12538G REPAIR PARTS LIFTTRACTOR - - MODEL NUMBER HD12538G PARTMOWER REPAIR PARTSTRACTOR - - MODEL NUMBER HD12538G REPAIR PARTS TRACTOR - - MODEL NUMBER HD12538GMOWER KEY PART NO. NO. DESCRIPTIONPEERLESS TRANSAXLE - MODEL NUMBER REPAIR PARTSTRACTOR - - MODEL NUMBER HD125386 MODEL NUMBER HD12538G 606 RingREF PART NO. NO REF PARTSERVICE NOTES CE NOTES CE NOTES SIGHTING ONLY RIDE UP AND DOWN HILL NOT ACROSS HILLSIGHT AND HOLD THIS LEVEL WITH SKY LINE OR TREE \ \ 7 - . - \