Weider 831.153933 specification

19.Route the Swivel High Cable (74) through the Swivel Upright (5) and over a 4 1/2” Pulley (119). Attach the Pulley inside the Upright with a 3/8” x 2 3/4” Bolt (101), two 3/8” Washers (91), two 1/2” Spacers (89), and a 3/8” Nylon Locknut (87).

Attach a 3/8” x 2 1/2” Bolt (18), two 3/8” Washers (91), and a 3/8” Nylon Locknut (87) to the Swivel Upright (5).

20.Remove the preattached 3 1/2” Pulleys (78) from the Small Pulley Plates (31).

Wrap the Swivel High Cable (74) over a 3 1/2” Pulley (78). Attach the Pulley and a Cable Trap (68) to the second set of holes from the top of the Small Pulley Plates (31) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure the Cable

Trap is turned to hold the Cable in the groove of the Pulley.

21.Wrap the Swivel High Cable (74) over a 4 1/2” Pulley (119). Attach the Pulley inside of the indicat- ed bracket on the Top Frame (6) with 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87).

22.Lift the Weight Tube (43) and the Top Weight (45) closest to the Swivel Upright (5). Make sure that the small pin on the Weight Tube is inside of the groove under the Top Weight.

Insert a Weight Pin (50) into the stack of Weights (44). Place a 1/2” Washer (1) on top of the Weight Tube (43). Tighten a 1/2” Nut (118) halfway onto the end of the Swivel High Cable (74). Screw the end of the Cable two full turns into the Weight Tube. Then, tighten the Nut against the 1/2” Washer.

23.Locate the Swivel Cable (17), which is 115 3/8” long and has an eyelet on each end. Attach the Cable inside the Top Frame (6) with a 5/16” x 2 1/2” Bolt (59), two 5/16” Washers (90), and a 5/16” Nylon Locknut (86).

19			91		18
		5	91		18
		5				101
						101
91						91
87						91
87					89
					89
91
87	89		119			74
			119
20
			74
			87
						100
			78	68		31
			31
21
						6
	93
						87
			119			74
22
						74
5						118
						118
50			45			1
			45
						43
						43
						44
23			59
			59			86
			90			86
						17
					6

Weider 831.153933 user manual Trap is turned to hold the Cable in the groove of the Pulley

Models: 831.153933

Trap is turned to hold the Cable in the groove of the Pulley.

19			91		18
		5	91		18
		5				101
						101
91						91
87						91
87					89
					89
91
87	89		119			74
			119
20
			74
			87
						100
			78	68		31
			31
21
						6
	93
						87
			119			74
22
						74
5						118
						118
50			45			1
			45
						43
						43
						44
23			59
			59			86
			90			86
						17
					6

19			91		18
		5	91		18
		5				101
						101
91						91
87						91
87					89
					89
91
87	89		119			74
			119
20
			74
			87
						100
			78	68		31
			31
21
						6
	93
						87
			119			74
22
						74
5						118
						118
50			45			1
			45
						43
						43
						44
23			59
			59			86
			90			86
						17
					6

19			91		18
		5	91		18
		5				101
						101
91						91
87						91
87					89
					89
91
87	89		119			74
			119
20
			74
			87
						100
			78	68		31
			31
21
						6
	93
						87
			119			74
22
						74
5						118
						118
50			45			1
			45
						43
						43
						44
23			59
			59			86
			90			86
						17
					6