2. Refer to drawing 2a. Press a 25mm Round Inner | 2 |
| 2a | 70 | 49 | |
Cap (49) into each end of the weight tube on the |
| |||||
19 |
|
|
| |||
|
|
|
|
| ||
Weight Carriage (19). Note: Make sure the |
|
| 19 |
|
| |
|
|
|
| 70 | ||
Square Slider Bushings (70) are assembled to |
|
| 49 |
| ||
|
|
|
| |||
the Weight Carriage and Weight Stop (67). |
| 70 |
|
|
|
|
|
|
|
|
|
| |
Turn the Weight Stop (67) so that the indicated |
| 67 | Hole | 70 |
| 67 |
hole is on the side shown and the Square Slider |
|
| ||||
|
|
|
| |||
Bushing (70) is on top. Slide the Weight Stop |
|
|
|
|
|
|
onto the Rear Upright (56). |
|
|
|
|
|
|
Refer to drawing 2b. Attach the Weight Stop |
| 56 | 42 |
|
| |
(67) to the Rear Upright (56) with an M8 x 70mm |
|
|
|
|
| |
|
|
|
|
|
| |
Bolt (11) and an M8 Nylon Locknut (3). |
|
|
|
|
|
|
Orient the Weight Carriage (19) as shown. Slide |
|
|
|
|
|
|
the Weight Carriage onto the Rear Upright (56). |
|
|
|
|
|
|
|
|
|
|
| 65 | |
Press a 25mm Square Inner Cap (65) into the |
|
|
|
|
|
|
Front Upright (42). Slide the Front Upright onto |
|
|
|
|
|
|
the M8 x 63mm Carriage Bolts (1) in the Base |
|
|
|
|
|
|
(4). Hand tighten an M8 Nylon Locknut (3) onto |
|
| 3 |
|
|
|
each Carriage Bolt. Do not tighten the Nylon | 2b | 56 |
|
|
|
|
Locknuts yet. |
|
|
|
| ||
|
|
| 4 |
|
| |
| 19 |
|
|
|
| |
| 67 |
|
|
|
| |
|
| 1 |
|
|
| |
| 3 |
| 11 |
|
|
|
|
|
|
|
|
| |
3. Press a 50mm Square Inner Cap (27) into the top |
|
|
|
|
|
|
of the Rear Upright (56). Press a 45mm Square | 3 |
|
|
|
|
|
Inner Cap (44) into each end of the crossbar on |
|
| 61 |
|
| |
the Top Frame (55). Press two 25mm Round |
|
| 55 |
|
| |
|
|
| 49 | |||
Inner Caps (49) into the top of the crossbar. |
|
|
| |||
|
| 8 |
|
| 44 | |
|
|
|
|
| ||
Attach the Top Frame (55) to the Front Upright |
| 27 |
|
|
|
|
|
|
|
|
|
| |
(42) with two M8 x 67mm Bolts (61), a Support |
| 8 |
|
|
|
|
Plate (8), and two M8 Nylon Locknuts (3). Attach |
|
| 3 |
|
| Crossbar |
the Top Frame to the Rear Upright (56) in the | 61 |
| 44 |
| ||
|
|
| ||||
same manner. |
|
|
|
|
| |
|
|
|
|
|
| |
Tighten the Nylon Locknuts used in steps |
| 56 | 3 | 42 |
|
|
|
|
|
| |||
ARM ASSEMBLY |
|
|
|
|
|
|
| 4 |
|
|
|
|
|
4. Press a 25mm Plastic Bushing (26) onto each |
|
|
|
|
|
|
welded spacer on the Press Frame (17). Slide the |
|
|
|
|
|
|
Press Frame onto the Base (4) so the Plastic |
|
|
|
|
| Lubricate |
Bushings are aligned with the indicated tube in |
|
| 17 |
|
| |
|
|
|
|
| ||
the base. Note: This will be a tight fit; the |
|
|
|
|
|
|
Plastic Bushings should fit over the ends of |
|
|
|
|
| 59 |
the tube in the Base. |
|
| 21 |
|
| 9 |
|
|
|
|
|
| |
Lubricate an M10 x 198mm Bolt (59). Attach the | 4 |
|
|
| Welded | |
|
|
|
| Spacers | ||
Press Frame (17) to the Base (4) with the Bolt, two |
| Tube |
|
| ||
| 9 |
|
|
| ||
M10 Washers (9), and an M10 Nylon Locknut (21). |
| 26 |
|
| ||
|
|
|
| |||
Note: Do not overtighten the Nylon Locknut; |
|
|
|
|
|
|
the Press Frame must be able to pivot easily. |
|
|
|
|
|
|
| 6 |
|
|
|
|
|
