2. Position the Crossbar (3) between the two | 2 |
|
|
|
|
|
Uprights (4). Note: Make sure the decal on the |
| Decal |
|
| Holes | |
|
|
| 35 | |||
Crossbar is in the position shown. Attach the |
|
|
|
|
| |
|
| 21 |
|
|
| |
Crossbar to each Upright with four M10 x 95mm |
|
|
|
| 4 | |
|
|
|
|
| ||
Bolts (34), two Support Plates (21), and four M10 |
| 3 |
|
|
|
|
Nylon Locknuts (35). Do not tighten the Nylon |
|
|
|
|
| |
|
|
|
|
|
| |
Locknuts yet. |
|
|
|
|
| 35 |
|
|
|
|
|
| |
|
| 34 |
|
|
|
|
|
| 21 |
|
|
| |
|
|
| 34 |
|
|
|
3. Attach the Frame (1) to the Crossbar (3) with two | 3 |
|
|
|
|
|
M10 x 95mm Bolts (34) and two M10 Nylon |
|
|
|
| 35 | |
|
|
|
|
| ||
Locknuts (35). Do not tighten the Nylon |
|
|
|
|
|
|
Locknuts yet. |
|
|
|
|
|
|
Press two 8mm Bushings (32) into the indicated |
|
| 34 |
|
| 3 |
locations on the Frame (1). |
| 32 |
|
| ||
20 |
|
|
|
| ||
|
|
|
|
| ||
|
|
|
|
|
| |
Press a 75mm x 50mm Inner Cap (20) into the |
|
|
|
|
|
|
Frame (1). |
|
| 1 |
|
|
|
|
|
|
|
|
| |
|
| 32 |
|
|
|
|
4. Press two 50mm Square Inner Caps (22) into the | 4 |
|
|
|
|
|
Front Stabilizer (2). |
|
|
|
|
| |
|
|
| 1 |
|
| |
|
|
|
|
| 35 | |
Attach the Front Stabilizer (2) to the Frame (1) |
|
|
|
|
| |
| 2 |
|
|
|
| |
with two M10 x 65mm Bolts (36), two M10 |
|
|
|
|
| |
|
|
|
|
|
| |
Washers (27), and two M10 Nylon Locknuts (35). |
|
|
|
|
|
|
Tighten the M10 Nylon Locknuts (34) used in | 22 |
|
|
|
| |
|
|
|
|
|
| |
steps |
| 36 | 27 |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| |
|
|
| 22 |
|
|
|
5. Press four 20mm x 40mm Inner Caps (43) into | 5 |
|
|
|
|
|
the Backrest Frames (10). Orient the Backrest |
|
|
|
|
| |
|
| 8 |
|
|
| |
Frames as shown. Note: The indents in the |
|
|
|
|
| |
|
|
|
|
|
| |
Backrest Frames must be on top. |
|
|
|
|
|
|
Attach the Backrest Bracket (9) to the Backrest |
|
|
| 40 |
|
|
Frames (10) with four M8 x 55mm Carriage Bolts |
|
|
|
| 43 | |
|
|
|
|
| ||
(40) and four M8 Nylon Locknuts (42). Do not |
| Indent |
|
|
|
|
tighten the Nylon Locknuts yet. |
| 10 |
|
|
| 19 |
|
|
|
|
| ||
Attach the Backrest (8) to the Backrest Frames |
|
|
|
|
|
|
(10) with four M6 x 50mm Bolts (39) and four M6 |
|
|
|
|
|
|
Washers (19). Do not tighten the Bolts yet.The |
| 43 19 |
|
| 39 |
|
Backrest must be oriented as shown. |
|
|
|
|
| |
|
| 39 |
|
| 42 |
|
|
|
|
|
|
| |
|
| 9 | 42 |
|
|
|
|
|
|
|
|
| |
| 7 |
|
|
|
|
|
