Pedicure Spa Specifications
*Hot and cold water supply lines required (hot and cold shut offs may be installed under pedicure spa base)
*Drain installation: References noted on page 9, standard unit comes w ith drain pump.
Overall dimensions without accessories, seat upright: 60"L (152cm) x 44"W (112cm) x 60"H (152cm)*
Overall dimensions, seat upright, both armrests open w\ cup holders exposed:
|
| 60”L (152cm) x 44”W (112cm) x 60”H (152cm) |
Without accessories, seat collapsed, both arms closed: | ||
|
| (Shipping position): 60”L (152cm) x 32”W (81cm) x 37”H (94cm)* |
Maximum area required for full chair and armrest movement: | ||
|
| 77”L (196cm) x 44”w (112cm) x 60”H (152cm)* |
Shipping dimensions: | 65”L (165cm) x 33”W (84cm) x 65”H (165cm)* | |
Empty weight: | 179 lbs. (81kg)* | |
Shipping weight: | 245 lbs. (102kg)* | |
Capacity of basin: | Will hold up to 6.0 U.S. Gallons; w ater level markings at 5.5 U.S. gallons | |
Whirlpool pump motor: | 110V: | 1/6 HP, 110V, 60Hz (alternate voltages available) |
| 220V: | 1/6 HP, 220V, 50/60Hz |
Seat and back motors: | 24V DC Linear Actuators. Spa requires 16” (41 cm) of space betw een pedicure | |
| spa and w all w ith standard actuator | |
Massage motor: | 12V AC, Adapter included (alternate voltages available) | |
Power source: | 110V: | 110V AC, 2.75 Amp, 60 Hz (GFCI Protected) |
| 220V: | 220V AC, 2.75 Amp, 50/60 Hz (GFCI Protected) |
Caution: Pedicure spa must be installed by a licensed electrician and a licensed plumber, conforming to all local and national electrical codes.
Construction:Metal Frame w ith Acrylic Fiberglass Shells,
Crystal Clean™
water massage grooves, no closed loop circulating pipes, 100% fully drained, and cleanable
Electrical switches: | On/Off sw itch for w hirlpool pump. A single |
| for massage motors, heat and seat/back position. Hot and Cold w ater supply |
| lines required. |
Compliances: | Complies w ith ASME/ANSI Whirlpool Bathtub Specs ASME/A NSI A112.19 7M- |
| 1995 and |
| Spray: Check valves comply w ith ANSI/ASME A112.18.3M, A112.18.1M, CSA |
| B125, and TÜV certified. |
Electrostatic Limits: | This unit may loose one ore more functions when electrostatic contact discharge |
| in excess of 4KV gets into accessible conductive part of the unit and can be |
| restored by resetting the unit. |
| This unit may loose one ore more functions when power surge in excess of 2KV |
| is applied to the AC input pow er port and can be restored by resetting the unit. |
| This unit may loose one ore more functions w hen subjected to fast transient |
| voltages in excess of 0.5KV at 5 KHz repetition frequency and can not be |
| restored. |
Limited warranty: | One (1) year from date of shipment. |
Due to our policy of continuous improvements, all specifications are subject to change without notice.
*Note: All dimensions and weights are approximate
Document ID:15080000 | Rev: E | Technical Support: | Page 11 of 20 |