Whirlpool 29-718, 35-718 installation instructions I& m, Panel C, 134 m

7.

terminal

bOX cover

6 m

Remove terminal box Cover from

Mae than one person is required to help with appliance intiallation because Of its weight and size.

Failure to tallow these instructions may result in personal injury.

7 Lift the range hood into final

l position and center. Mark on the

U’nderside of cabinet the location of the four kc3 hole mounting slots. set IOn”* hnnrl

?k ,I protected surface. aside L. ( - r

Numbers correspond to steps.

Ta wire through rear, mark a line 7-l /2” from the right of the centerline on the Wall. Mark the point on this line that is 64-s/8” from the floor (or I -3/8” from underside of cabinet).

Drill a T-1/4” diameter hole through Wail at this point’

To vent through wall with 3- 1/A” X 10” rectangular ductwork, measure from floor n 65-7/r and 62-3/8” (or l/8” and 3-5/8” dOW from underside of cabinet) and mark on back wall, Measure and mark a line !5-1/4” to right and left of centerline connecting ‘the two lines, Use a saber SUWt0 Cut a rectangular opening for the ductwork.

31,

n rm

Install ductwork through the vent opening in upper cabinei or wall. Complete venting

system according to method needed. See *\/entina requirements. NUse caulking to

8 m

Determine and clearly mark a vertical centerline on the wall and cabinet in the area the vent opening will be made.

Towirethrolthrough top, mark a line 7-112” from the right. of_the” centerline on the underside of the cabinet, Mark the point on this tine thatthe is l-3/8” from back wall. Drill a 1-l /4” diameterdie,..-.-. hole through the cabinet at this point.

Panel C

To vent through the roof with 7” round ducfwark mark 4-l /2” and 5” in from back wait atoni the centerline on underside Of cabinet, Use these points as centers t0 draw 7-1/g” circles on underside of cabinet. Use a saber saw to cut the openings for the ductwork Repeat for the underside of the top of the cabinet, Thiswill create slotted openings,

To vent through the roof with 3-j /4” X 10 rectangular ductwork, mark a line 1” and 5” from the buck wall on the underside of the cabinet Mark lines 5-l /4” to the right and left of the centerline on the underside of cabinet that connect the lines just drawn. Use a saber saw to cut a EdangUlar opening far the ductwork. Repeat for the underside of the top of the cabinet,

I& m

,Kach rectangular damper to selectea >.ctanguiar vent opening, If damper is &ached to back of range hood, be Sure jamper hinge istoward the top. Far round ented installations, use round damper in juct to prevent air from flowing back into

juclwork, If roof cap has a damper, -‘-.-rrh, k-‘....Ac’^Cm,-,-rnnne, hood,

4

134 m

Run wiring through wall of cabinets according to the National Electricai Code and local codes and ordinances. DONot turn on power until installation is complete.

keyhole slot

Start screws through neck of each of the four keyhole mounting screw slots marked on the cabinet bottom,

Lift-range hood into final position, feeding elcbctrical wire through wiring opening, PO&ion the range hood so that the large

,d of the keyhole slots are over the screws, 7; en push the hood toward the wall SOthat thee screws are in the neck of the SlOtS. Ticlhten mounting screws to cabinet, mloking sure mounting screws are in narrow

,, _._-

ne-!ck.. of slots, Make sure that damper blade. if used, rot&es up and down treW~