Whirlpool 9763375 Installation Requirements, Tools and Parts, Location Requirements

Models: 9763375

1 28
Download 28 pages 10.57 Kb
Page 4
Image 4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the safety instructions provided with any tools listed here.

Tools needed:

level

drill with 1¹⁄₄" (3 cm), ³⁄₈" (9.5 mm), ⁷⁄₆₄" (2.75 mm) and ¹⁄₈" (3 mm) drill bits

pencil

wire stripper or utility knife

measuring tape or ruler

pliers

caulking gun and weatherproof caulking compound

duct tape

jig saw or keyhole saw

flat blade screwdriver

metal snips

Phillips screwdriver

Parts needed:

1 x ¹⁄₂" conduit

1 wall or roof cap

metal vent system

2 charcoal filters – for non-vented (recirculating) installations only

Parts supplied:

Remove parts from packages. Check that all parts were included.

hood canopy assembly with ventilator and light bulbs installed

deflector for non-vented (recirculating) installations

plastic transition with back draft dampers installed

Installation Instructions and Use & Care Guide

filter(s) – depending on model and size

screws and drywall anchors

2 mounting hooks

vent cover support bracket

mounting template

2 piece vent cover

rubber tape

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Canopy hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

Grounded electrical outlet is required. See “Electrical requirements” section.

The canopy hood is factory set for venting through the roof or wall. For non-vented (recirculating) installations see “Non-vented (recirculating) installations” in “Prepare Mounting Location” section.

All openings in ceiling and wall where canopy hood will be installed must be sealed.

Product Dimensions

8"

(20.3 cm)

6³⁄₄"

(17.1 cm)

upper vent

 

 

 

 

 

 

 

 

 

 

 

9

⁵⁄₈" (24.4 cm) min.

 

 

 

 

cover

 

 

 

 

 

 

 

 

26" (66.0 cm) max.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

26" (66.0 cm)

 

 

 

 

 

 

 

 

 

 

min.

 

lower vent

 

 

 

 

 

 

42

³⁄₈" (107.6 cm)

 

cover

 

 

 

 

 

 

 

 

 

16³⁄₄"

 

 

 

max.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(42.5 cm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9¹⁄₂"

(24.1 cm)

20³⁄₁₆"

 

 

30" (76.2 cm) or

(51.3 cm)

 

 

36" (91.4 cm)

 

 

 

 

 

 

 

 

NOTE: For reduced ceiling height vented and non-vented (recirculating) installations, only the upper vent cover, which is 26" (66.0 cm), is used.

4

Page 4
Image 4
Whirlpool 9763375 Installation Requirements, Tools and Parts, Location Requirements, Product Dimensions