How Auto Moisture Sensing Plus works

The Even-Heat™ feature improves drying performance with Auto Moisture Sensing Plus, which advances the cycle as moisture is extracted from clothing. A thermistor (electronic temperature sensor) and moisture sensing strips in the dryer drum help measure the amount of moisture in the clothes as they pass. An electronic control determines the load type to help save time, avoid overdrying, and increase the accuracy of the end dryness level. After the first 5 minutes of an automatic cycle, the estimated time display will adjust based on the approximate load size, cycle, dryness level selected and amount of moisture left in the clothes. When the clothes have reached approximately 80% of the dryness level selected, the estimated time display will adjust again, showing the final drying time. Auto Moisture Sensing Plus takes the guesswork out of drying time and enhances fabric care.

To use a Manual Cycle

Rotate the dial to select a Manual Cycle.

Press the MANUAL DRY TIME (- or +) buttons until the desired drying time is displayed. Tap - or +, and the time will change by 1-minute intervals. Press and hold - or +, and the time will change by 5-minute intervals. The initial time displayed is the actual drying time.

NOTE: The Manual Dry Time feature can be used only with Manual Cycles.

Press TEMP until the desired temperature glows.

NOTE: Pressing the Dryness Level button will cause the triple beep indicating that this option is not selectable. Also, a Dryness Level is not indicated.

Press the EXTRA CARE feature button if this option is desired.

Press the CYCLE END SIGNAL button to set volume to desired level.

Press (and hold) HOLD TO START button until dryer starts (about 1 second).

While a Manual Cycle is running, you can change the settings for Time, Temperature, the Extra Care feature, and the Cycle End Signal. Press the OFF button twice to stop the dryer and clear the settings, allowing you to select another cycle.

Stopping Your Dryer

To stop your dryer at any time

Press OFF twice or open the door.

Pausingor Restarting

To pause the dryer at any time

Open the door or press OFF once.

To restart the dryer

Close the door and press (and hold) HOLD TO START button until dryer starts.

NOTE: Drying will continue from where the cycle was interrupted if you close the door and press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will shut off.

Select new cycle settings before restarting the dryer.

Control Locked

This feature allows you to lock your settings to avoid unintended use of the dryer. You can also use the Control Locked feature to avoid unintended cycle or option changes during dryer operation.

To enable the Control Locked feature when dryer is running:

Press and hold the CYCLE END SIGNAL button for 3 seconds. The control is locked when a single beep is heard and the Control Locked status light is on.

When the dryer is off, it is not necessary to press the Control On button before activating the Control Locked feature.

To unlock:

Press and hold the CYCLE END SIGNAL button for 3 seconds to turn this feature off.

NOTE: When the dryer is running and Control Locked is on, the dryer can be stopped by pressing the Off button, but can’t be restarted until the control is unlocked.

Drying and Cycle Tips

Select the correct cycle and dryness level or temperature for your load. If an Automatic Cycle is running, the display shows the estimated cycle time when your dryer is automatically sensing the dryness level of your load. If a Manual Cycle is running, the display shows the exact number of minutes remaining in the cycle.

Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level.

Drying tips

Follow care label directions when they are available.

If desired, add a fabric softener sheet. Follow package instructions.

Remove the load from the dryer as soon as tumbling stops to reduce wrinkling. This is especially important for permanent press, knits and synthetic fabrics.

Avoid drying heavy work clothes with lighter fabrics. This could cause overdrying of lighter fabrics, leading to increased shrinking or wrinkling.

Cycle tips

Dry most loads using the preset cycle settings.

Refer to the Automatic or Manual Preset Cycle Settings chart (in the “Cycles” section) for a guide to drying various loads.

Drying temperature and Dryness Level are preset when you choose an Automatic Cycle. You can choose a different dryness level, depending on your load by pressing the DRYNESS LEVEL button to select MORE or LESS.

If you wish to adjust the cycle length of a Manual Cycle, you must press the MANUAL DRY TIME (- or +) buttons. Adjust the temperature of a Manual Cycle by pressing TEMP until the desired temperature is selected.

NOTE: You cannot choose a Dryness Level with Manual Cycles.

16

Page 16
Image 16
Whirlpool FRONT-LOADING GAS DRYER manual Stopping Your Dryer, Pausingor Restarting, Control Locked, Drying and Cycle Tips

FRONT-LOADING GAS DRYER specifications

The Whirlpool front-loading gas dryer is a pinnacle of modern laundry technology, combining efficiency, performance, and convenience. Designed to meet the demands of busy households, it offers a range of features that simplify the drying process while ensuring optimal results for all types of fabrics.

One of the standout features of this gas dryer is its advanced moisture sensing technology. The sensor detects when clothes are dry and automatically stops the cycle, preventing over-drying and saving energy. This not only protects garments from damage but also reduces energy consumption, making it an environmentally friendly choice.

In terms of capacity, the Whirlpool front-loading gas dryer boasts a generous drum size that accommodates large loads, allowing users to spend less time doing laundry. The smooth surface of the drum prevents snagging, which is especially important for delicate items. The dryer also features multiple drying cycles, including options for heavy-duty and delicate fabrics, ensuring tailored care for each load.

Moreover, the dryer is equipped with the EcoBoost option, which utilizes a lower heat setting and extended drying time to save energy without compromising drying quality. This makes it an ideal choice for the eco-conscious consumer seeking to reduce their carbon footprint.

Another remarkable characteristic of this gas dryer is its steam-enhanced cycles. The steam feature helps to reduce wrinkles and odors, providing a fresh finish to garments straight from the dryer. This is particularly beneficial for busy individuals who need to look sharp without the hassle of ironing.

The control panel of the Whirlpool front-loading gas dryer is designed for user-friendliness, featuring a clear display and intuitive controls that allow for easy selection of drying settings. The Wrinkle Shield option is also included, which periodically tumbles the load after the cycle ends to keep wrinkles at bay.

Safety is a key consideration in the design, and this dryer includes a lint screen that is easy to clean, ensuring that the appliance operates efficiently and safely.

In conclusion, the Whirlpool front-loading gas dryer is an excellent addition to any laundry room, providing a blend of advanced technologies, thoughtful features, and superior drying performance. Whether tackling everyday laundry or special care items, this dryer delivers on the promise of quality, efficiency, and convenience.