iiiiii!iE'ectrica'connectioncable from
junctionpower supply
box _
red_
white _
cable from
junction power supply
Electrical Shock Hazard
Disconnect power to the junction box before making connection.
Electrically ground oven.
Connect ground with
w_re | _ |
| |
grounding | oven |
| |
cable wires |
| ||
factory crimped |
| ||
Figure 1 | cable from | conduit | |
oven | connector | ||
| |||
Figure 2 | cable from | connector |
| oven |
|
Failure to follow these instructions could result in death, fire or electrical shock.
This oven is manufactured with white (neutral) power supply wire and a
Feed oven cable through opening in
• the cabinet. Make electrical connection
following the steps needed for your installation.
1. Disconnect the power supply.
2. Remove the junction box cover.
3. Connect oven cable to junction box through the
4. Connect the two black wires together with
5. Connect the two red wires together with
6. Complete electrical connection according to local codes and ordinances.
If local codes PERMIT connecting
7.Connect the
to the neutral (white) wire in junction box. See Figure 1.
8.Replace junction box cover.
If local codes DO NOT PERMIT
connecting
wire in junction box:
7.Separate the
8.Connect white oven cable wire to neutral (white) wire in junction box. See Figure 2.
9.Connect the bare grounding oven cable wire to a grounded wire in the junction box. See Figure 2.
10.Replace junction box cover.
If connecting to a four-wire electrical system:
7.Separate bare and white oven cable wires.
8.Connect white oven cable wire to neutral (white) wire in junction box. See Figure 2.
9.Connect the bare grounding oven cable wire to the green grounding wire in junction box. Do Not connect bare grounding wire to neutral (white) wire in junction box. See Figure 2.
10. Replace junction box cover.
li tA.ac"ment
Carefully push against seal area of oven front frame when pushing oven into cabinet.
Do Not push against outside edges.
•Lift oven into cabinet cutout using the oven opening as an area to grip.
0
J
-
4 screws
J
J
J
8• Replace oven racks.
ratingImportant:plateReplaceontheupperthedoorovenwith. the model/serial
On some models, the construction of this door is
designed to withstand
\ | oven frame |
hinge slot |
door hinge
Replace the single or upper oven door by
• inserting ends of hinges into hinge slots in
shipping foot
Push against seal area of front frame to push oven into cabinet until shipping feet almost contact cabinet. Use a Phillips screwdriver to remove screws attaching shipping feet. Remove and discard shipping feet.
Push oven completely into cabinet and center oven in cabinet cutout.
• Important: Securely fasten oven to cabinet
using the screws provided (two screws for a single oven or four screws for a double oven). Insert the
screws through holes in mounting rails. Do Not overtighten screws.
Slide top of trim up,
Pushtrim
into place. Replace
trim screw.
• Slide top end of each trim upward onto oven
side rails. Push each trim into place at bottom of trim. Use screws to attach each trim to oven. Take care not to scratch other surfaces with ends of trim.
oven frame. Push behind each hinge so that hinges are pushed into oven frame as far as they will go. Open door and remove both door removal pins. Close and open door to check that door closes and opens completely. If door does not close or open completely, you have not pushed hinges completely into frame. Repeat door removal step and reinsert door into hinge slots again.
Repeat for lower oven door.
Ii!i#IC,e°,o,erot,o.
0• Turn on power supply. The display
panel will light up briefly. "PF" should appear in the temperature display.
BAKE BROIL
Check the operation of your single oven.
Press the "BROIL" pad. "BROIL" will appear in
the display. Press the "START" pad. Make sure the oven door is closed and the "ON" light is shown in
the display area. After 2 minutes, partially open oven door. You should feel heat from the oven.
Press the "CANCEL" pad.
Check the operation of your double oven. Press the "Upper Oven" pad. Pressthe "BROIL" pad. "BROIL" will appear in the display. Press the "START" pad. Make sure the oven door is closed and the "ON" light is shown in the display area. After 2 minutes, partially open oven door. You should feel heat from the oven. Pressthe "CANCEL" pad.
Press the "Lower Oven" pad and repeat the steps you completed for checking the upper oven.
If your oven does not heat or an "F", followed by a number, appears in the display, contact your dealer or check the "If you need service..." section of this Installation Instructions.
To get the most efficient use from your new oven, read your
Use and Care Guide. Keep Installation
Instructions
and Guide close to oven for easy reference.
Page 3
