Whirlpool 338, 2314183 manual RefrigeratorDoors, Remove Doors and Hinges all models

RefrigeratorDoors

TOOLS NEEDED: ⁵⁄₁₆" hex-head socket wrench, #2 Phillips screwdriver, flat-blade screwdriver, ⁵⁄₁₆" open-end wrench, flat 2" putty knife.

IMPORTANT:

■All graphics referenced in the following instructions are included later in this section after “Final Steps.” The graphics shown are for a right-hand swing refrigerator (hinges factory installed on the right).

■If you only want to remove and replace the doors, see “Remove Doors and Hinges” and “Replace Doors and Hinges.”

■Depending on your model, you may have standard (Style 1) or contour (Style 2) doors. If you are going to reverse the door swing, follow the instructions for the appropriate door style.

■Before you begin, turn the refrigerator control OFF, and remove food and adjustable door or utility bins from doors.

Remove Doors and Hinges (all models)

⁵⁄₁₆'' Hex-Head Hinge Screw

1.Unplug refrigerator or disconnect power.

2.Open refrigerator door and remove base grille from the bottom front of the refrigerator. See Base Grille graphic.

3.Close the refrigerator door and keep both doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

4.Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the freezer door free from the cabinet.

5.Remove the parts for the center hinge as shown in the Center Hinge graphic. Lift the refrigerator door free from the cabinet.

6.Remove the parts for the bottom hinge as shown in the Bottom Hinge graphic.

Reverse Doors–Standard Door (optional)

IMPORTANT: If you want to reverse your doors so that they open in the opposite direction, follow these steps. If you are not reversing the doors, see “Replace Doors and Hinges.”

Door Stop Screw	Door Hinge Hole Plug
Door Handle Sealing Screw	Cabinet Hinge Hole Plug
Flat-Head Handle Screw	Door Handle Screw Cover
Door Handle Seal Screw Front	Round-Head Handle Screw

Cabinet

1.Remove ⁵⁄₁₆" hex-head hinge screws from the handle side and move them to the opposite side. See Graphic 1-1.

2.Remove the cabinet hinge hole plugs from the cabinet top and move them to the opposite side hinge holes as shown in Graphic 1-2.

Freezer door

1.Remove freezer handle assembly as shown. Keep all parts together. See Graphic 2.

2.Remove the door hinge hole plug. Move it to the opposite side as shown in Graphic 3.

3.Remove the door handle sealing screws. Move them to the opposite side of the freezer door as shown in Graphic 4.

4.Remove the door stop. Move it to the opposite side of the freezer door as shown in Graphic 5.

5.Position the freezer handle on opposite side of freezer door. Assemble handles on the door as shown in Graphic 2.

6.Tighten all screws. Set aside the door until the hinges and refrigerator compartment door are in place.

Refrigerator door

1.Remove refrigerator handle bottom trim. For Style 1, remove the handle screw cover. See Graphic 6-1. For Style 2, slide trim down as shown in Graphic 6-2.

2.Remove the refrigerator handle assembly as shown. Keep all parts together. See Graphic 6-3.

3.Remove the door hinge hole plug from refrigerator door. Move it to the opposite side hinge hole as shown in Graphic 3.

4.Remove the door handle sealing screws. Move them to the opposite side of the refrigerator door as shown in Graphic 4.

5.Remove the door handle seal screw front. Move it to the opposite side of the refrigerator door as shown in Graphic 7.

7